Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FDB636GFR0

FDB636GFR0 Frigidaire Dishwasher - Overview

Get Parts and Repair Help for FDB636GFR0

If you know the dishwasher repair part you need, you can browse the list of all parts on the FDB636GFR0, or you can search by name or part description. You can also find your part by where it is located on the FDB636GFR0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for FDB636GFR0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.36

Tub Gasket - Gray

This dishwasher door gasket creates a seal around the dishwasher to ensure that water is not able to leak out. If this was not in place there would be a gap between the opening of ...

$55.63

Lower Dishrack Assembly

This white lower dishrack assembly comes with eight light-gray rollers for easy access. The dishrack is approximately 21 inches wide x 22 inches deep. The dishrack holds dishes in place during the dishwashing cycle. If you see rust spots on the dishes, the lower rack will not pull out, or the lower rack is visibly rusted or damaged, you will need to replace the part. Other common symptoms include: unusual or loud noises coming from the unit, or the dishes on the lower rack not being washed properly. This part is also known as a dish rack or a dishwasher rack.

$26.85

Water Inlet Valve - 120V 60Hz

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close ...

$43.53

Upper Dishrack with Wheels

The upper dishrack, a vital part in a dishwasher, holds the dishes in place as the dishwasher goes through its cycle. If the wheels are missing/broken, the upper rack is damaged, or it starts to rust, replacing and installing a new dishrack could solve this problem. Customers rate this installation process as easy and no tools are required. Make sure to remove any items on the top rack before unhooking the tab of the rack stop on both ends and pulling it from the rail. Next step is to remove the upper spray nozzle and replace it with new one. Refer to the manual instructions for further guidance.

$6.03

Single Rack Roller Kit

The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not c...

$3.73

Heating Element Brass Nut

The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step guide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.

$17.40

BASKET

The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small...

$5.08

ROLLER TUB GREY

Sold individually. Grey in color.

$29.36

Lower Spray Arm with Shield

Located on the lower half of the dishwasher, the lower spray arm rotates and sprays water to clean the dishes in the washer. It does this when water is pushed through the spray arm...

$39.42

Door Latch and Gasket

Black in color. No longer available in almond. This door latch prohibits the dishwasher from operating when the door is open. The gasket is used around the door to keep the dishwasher from leaking.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking from Inlet Valve

  • Customer: CHRIS from ROANOKE, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 574 of 585 people found this instruction helpful
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first ... read more

Lower Rack Roller Missing

  • Customer: Sandra from Mount Vernon, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 365 of 367 people found this instruction helpful
Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new. read more

Leak in the water inlet valve/solinoid

  • Customer: Mickey from Ooltewah, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 142 of 155 people found this instruction helpful
1. Shut off water supply.
2. Removed inlet water hose where it connects to the vavle assembly.
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection from the solinoid.
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical con... read more