Parts That Fix Frigidaire Washer FAFS4474LW0 Leaking
Upgrade your home appliance with the Frigidaire Boot Seal Retaining Ring. An original and genuine replacement fastener, this quality piece ensures lasting durability and efficient performance. Specially designed for easy installation, this spring-held bellows clamp secures the door boot in place, enhancing the functionality and longevity of your washing machine. Please make sure that before purchase, your model is compatible with this product to assure accurate fitting. Remember to unplug your washer beforehand and wear work gloves during installment for optimum safety. Choose this genuine Frigidaire part for reliable, worry-free maintenance.
Replacing your Frigidaire Washer Spring-Held Bellow Clamp
Customer Repair Stories
-
Anthony from Fallbrook, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
Ensure proper drainage and protect your washer from damage with this durable tub-to-pump hose, designed for front-load washing machines. This genuine replacement part carries water from the tub to the drain pump and features a built-in coin trap to catch small objects that may fall from pockets during the wash cycle. Made from sturdy black rubber for long-lasting performance, the hose measures approximately 9.75 inches in length. Installation is simple—unplug the washer, shut off the water supply, and wear gloves for safety before removing the old hose and securing the new one in place.
This is a door striker, it is gray in color and is a part found on your washer. The purpose of the striker is to keep your washer door closed for usage. This piece will attach to your appliance lid and will activate the door switch when your lid is closed. The most common reasons for needing to replace this part are if your lid will not consistently open or close, and your washer will not consistently start. The only tool you will need to complete this installation is a Phillips screwdriver.
Replacing your Frigidaire Washer Door Striker
Customer Repair Stories
It got more complicated when too many striker tips broke off inside the latch assembly and prevented the tip of the new striker from going inside. To get at the latch assembly, I had to remove the big rubber g ... Read more asket that connects the drum to the frame of the machine. I removed this at the drum end. Big mistake! It took two of us to get the gasket back onto the drum, and I had to take the frame end of the gasket off anyway. That end is a lot easier to put back on. Anyway, I finally got to the latch assembly, which attaches to the machine with two screws. It has 3 connectors and the housing is a grey plastic clamshell that latches in 3 places. It came apart and parts came out. Jamming the latches open and very gently prying the clamshell open may let you escape the small parts barrage. Once I got everything back together, it all worked.
Unfortunately, the story doesn't end there. This machine has broken 4 strikers. They break during the wash cycle. Taking a cue from a previous DIY description on this site, I took the hinge apart. It looks like there is a part missing, because there isn't anything that keeps the door aligned with the rest of the machine. The door drops down as low as it can go on the hinge pin and the plastic of the door frame rides directly on the arm of the hinge part. I've shimmed it up about 3/16" temporarily, and it seems to work, but I can't escape the idea that I shouldn't have to do this...
-
Berend from New Haven, VT
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers
-
Joy from Columbia, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This hose moves detergent or water into the tub. Replace if leaking or clogged. This part is designed to keep your appliance operating reliably and efficiently. Replacing a worn or failing component helps prevent further issues and can extend the overall lifespan of your unit.
Replacing your Frigidaire Washer Dispenser to Tub Hose
This water inlet valve works with washers
Customer Repair Stories
-
Curtis from Lakeland, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Also known as a Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle and to prevent water from leaking. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
Customer Repair Stories
-
Charles from Mabank, TX
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
This part is located between the front and rear outer tubs.
This is a door hinge with bushings and works in conjunction with your washer. The purpose of this part is to attach to the outside of the front door panel to help with the lid opening and closing properly. The hinge will fasten the front panel of the washing cabinet to the lid of the washer. This piece is roughly 9 inches long, almost 3 inches high, and roughly 2.5 inches wide. The reason for needing to replace this part is if your lid/door will not open or close properly, which may lead to leaking.
Replacing your Frigidaire Washer Door Hinge with Bushings
Customer Repair Stories
Once hinge screws were removed I put a towel down on a counter to keep the front of the door from getting ... Read more marked up and proceeded to remove all of the screws around the back of the door so that I could lift the frame up enough to remove the broken hinge and insert the new hinge. It was a bit tricky to get the new hinge with bushings in place. I gently lifted the frame up with a flat head screw driver to widen the opening so I could get the bushings on the new hinge into position on the frame. Make sure they are properly inserted before you start tightening up screws.
Next, replaced all the screws on the frame, returned to the washing machine with helper who held the door up while I aligned the holes in the new hinge to the holes in the frame around the opening to the washer.
After everything was secured and tightened, to my surprise, the door latch did NOT line up with catch without lifting up about a 1/4" or a little more, on the bottom of the door. If someone slams the door without doing that you could break off part of the plastic latch or damage the catch inside the door frame.
I believe the original holes on the door frame were not drilled precisely during the manufacturing process and that is why the bottom bushing broke. We have always had to lift up a bit on the door to line up the latch with the catch. Eventually the strain on the bottom bushing caused it to break and then the door tilted down so you had to lift it up about 3/4 inch to latch it. I bought new hinge because if the top bushing broke the door could have come off.
Next time I buy a washing machine, I will pay more attention to the line up of the door latch with the door catch.
Flashlight helped me line up the holes.
-
John from Dover, NH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
-
RALPH from GREENFIELD, IN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This door boot spring clamp is a genuine replacement part that secures the rubber door seal on a front-loading washer, helping maintain a tight, leak-free seal during each wash cycle. It's commonly used to replace a worn or stretched clamp that can cause leaks or allow the door boot to shift out of place. Installing a new clamp helps keep the seal stable and ensures reliable washer performance. Be sure to check your model number to confirm the correct fit for your appliance.
With the GE Single Serve Hot Water Tank, you'll never be without hot water from your refrigerator dispenser whenever you need it. This crucial component safely stores and warms your water so it's always ready at a moment's notice. So why is this part so important? Well, without it, your refrigerator's hot water dispenser simply wouldn't function. Also, it's an easy way to give your GE refrigerator a performance boost, bringing it back to its original tip-top shape! Installation is simple, although it's wise to keep a few things in mind: don't forget to unplug your refrigerator and, for added safety, switch off the water supply. Clearing out any perishable foods is also key, as they could spoil without power. And during installation, wearing work gloves is a good idea?it's always better to be safe than sorry! Enhance the convenience of your kitchen experience and restore your GE refrigerator to its peak performance with this handy hot water tank. Trust us, this small investment is a big help in keeping your life running smoothly.
Replacing your Frigidaire Washer Door Glass
Customer Repair Stories
-
Lillian from PHILADELPHIA, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
-
Gennaro from Nutley, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the door does not open or lock. Your washer will not start if the door does not lock. This part is also known as a washing machine door lock assembly. As per the manufacturer, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would require the door lock kit.
Replacing your Frigidaire Washer Front Load Washer Door Lock and Switch Assembly
Customer Repair Stories
-
Keith from Sayville, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
-
DOUG from KING FERRY, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
The door outer panel is the exterior portion of the door and attaches to the door inner panel.
Sold individually.
Replacing your Frigidaire Washer Dispenser Inlet Gasket
