This high limit thermostat is used in a dryer and monitors the temperature to make sure it does not exceed 260 degrees Fahrenheit. When your dryer temperature reaches 260 it will cut it out and only c...
$85.85
In Stock
Order within the next 12 hrs and your part ships today!
This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to the floor or wobbling...
$25.82
In Stock
Order within the next 12 hrs and your part ships today!
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$11.21
In Stock
Order within the next 12 hrs and your part ships today!
This is a genuine replacement drum roller for a dryer. This part includes a roller which has an axle and two tri-rings. The dryer drum roller holds the drum in place while it rotates on the dryer supp...
$62.82
In Stock
Order within the next 12 hrs and your part ships today!
This part is the replacement screw for your washer. The head is approximately inch in diameter and the screw is approximately 3/4 inch in length. It is made of metal and is sold individually. This is...
$9.26
In Stock
Order within the next 12 hrs and your part ships today!
This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is u...
$210.30
In Stock
Order within the next 12 hrs and your part ships today!
Questions And Answers for EIMED60JIW6
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rhonda
October 7, 2022
I need to replace the part that is in front of the piece that you take out to clean the lint baffle. I don't know what that part is called. It cracked and we took it off. I am afraid that things will get blown out of the drum and into the bottom of the dryer.
For model number EIMED60JIW6
Hello Rhonda, thank you for contacting us. We have researched the model you have provided and have found that the part you are looking for is the lint filter, part number PS8770145. If you would like assistance placing an order, please contact customer service. Good luck with your repair!
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replac
... Read moreing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
By undoing the single screw which holds the sensor in place, the old one falls off. To replace: simply pop the two wires on their connections (small metal studs on the back), slide clip/wire end of sensor in place and replace the screw. You are back in business! Very simple repair that a DIY can save a ton!
1. Loosened the 3 screws inside of the drum 2. Removed the entire back of the dryer (lots of screws) 3. Removed the old vent (there are 2 screws at the bottom that hold it in) 4. Install new vent (put the screws back in) 5. Close up back and proceed to put all of the screws back
