Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
The drum belt attaches to the motor pulley and causes the drum to spin as the motor is rotating. The drum belt is made of black rubber. This is an easy repair and should only take a few minutes. This ...
This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, ...
This is a thermistor, also known as a dryer thermistor. The thermistor is attached to the blower housing, it will help regulate and oversee the temperature within the dryer. The most common symptom of...
This idler pulley assembly is sourced from the original manufacturer for use in dryers. The assembly includes the pulley wheel and bracket. It is found near the motor where it provides tension to the ...
The drum support roller and axle, which includes the roller shaft and mounting clips, is used in dryers. This part holds the drum as it rotates on the support wheels. When the roller begins to wear ou...
This thermostat is a genuine OEM part and is manufacturer-approved for electric dryers. The thermostat is responsible for monitoring and maintaining the temperature inside the dryer during the drying ...
The thermal fuse measures the air temperature inside your dryer drum, and turns the heat on and off to maintain the optimal temperature during the drying cycle. If your dryer will not start, dry cloth...
This genuine OEM heater duct assembly in your dryer directs hot air into the drum during operation. Generally, it can be found behind the drum or at the rear of the dryer. If this assembly becomes dam...
This moisture sensor plate is specifically designed to fit with your Samsung dryer. It is made of stainless steel and measures approximately 5 inches long. It is designed to detect the amount of moist...
This lint screen case, or lint filter case is specially designed for Samsung dryers. It is responsible for securing the lint screen inside the lint screen housing and preventing it from falling out. T...
This thermal cut-off fuse bracket assembly is a genuine replacement part supplied directly by Samsung for use in dryers. It is a safety component that is designed to protect the dryer from overheating...
$63.64
In Stock
Order now and your part arrives by May 9
Questions And Answers for DVE50M7450W
Ask our experts a question about this model and we'll get back to you as soon as possible!
12 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
El
March 29, 2024
hi. I'm getting an error of "dC" on my dryer. I recently change the heat assembly. The old one broke. I'm a bit confused if I should change the door switch or the door detection sensor. I'm not certain if they are the same. I'm thinking they are not based on the owner's manual. Thank you.
For model number DVE50M7450W
Hi El, thank you for reaching out. This error code indicates a problem with the door, most commonly the door switch, part number PS4210965. Check the door latch to see if it fits into its slot correctly and the door is firmly closed. If the door is closed properly and still the error appears, then you have a defective door switch, and need to be replaced to fix the issue. We hope this sorts out your problem!
Dryer will start and runs well, only after pressing the start button multiple times.
For model number DVE50M7450W
Hello Salvatore, thank you for your question. There are a few different parts you will have to check to isolate the problem. They are the Control Panel Assembly, Electronic Control Board, and Wire Harness to the control board. Let us know if you have further questions!
Did this question help you?
Thank you for voting!
Randy
March 15, 2023
Dryer run for about 10 minutes then stops heating any tips
For model number DVE50M7450W
Hi Randy, thank you for contacting us. According to our research, the issue might be with the heating element, part number PS4205218, or the high-limit thermostat, part number PS11741822. The thermostat might be cutting the gas supply prematurely, even before the burner temperature exceeds the safe operating temperature. We would recommend checking these parts for continuity using a multimeter. We hope this helps, good luck with the repair!
Hello Mickey, thank you for contacting us. Based on the description that you have provided, we would recommend checking the thermistor, part number PS4204984, to solve the problem. We hope this helps.
Well it went really well until the dryer was put back together as it still didn’t heat. The dryer was taken apart again. This time the thermistors &fuse was tested. Alas, the new fuse was faulty. After putting the car lid fuse back on n, the dryer worked again
YouTube, YouTube, YouTube. I YouTubed many videos on how to take a dryer apart to reach the drum support roller and axle. After watching numerous videos, I settled on one that had my exact model of dryer. For my dryer, previous inputs said I needed two rollers to for my model. That is not the case. My model actually has 4 rollers, 2 in th
... Read moree front and two in the back. I ordered 2 initially but only needed 1 thankfully since only one roller was bad. Keep it simple stupid is how I got it done. Dryer's are pretty simple machines mechanically. Don't trash your noisy dryer. We bought ours in 2014 and it only recently started giving us issues. This is after 2 moves and being run daily for a family of 6. I'm glad I found partselect.com. They saved me a ton of money.
