DVE50BG8300VA3 Samsung Washer - Overview
Models starting with DVE50BG8300VA3
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Drive Belt
PartSelect #: PS4133825
Manufacturer #: 6602-001655
The drum belt attaches to the motor pulley and causes the drum to spin as the motor is rotating. The drum belt is made of black rubber. This is an easy repair and should only take a few minutes. This ...
$53.32
On Order
Thermistor
PartSelect #: PS4204984
Manufacturer #: DC32-00007A
This is a thermistor, also known as a dryer thermistor. The thermistor is attached to the blower housing, it will help regulate and oversee the temperature within the dryer. The most common symptom of...
$40.02
In Stock
Idler Pulley Assembly
PartSelect #: PS11771601
Manufacturer #: DC93-00634A
This idler pulley assembly is sourced from the original manufacturer for use in dryers. The assembly includes the pulley wheel and bracket. It is found near the motor where it provides tension to the ...
$59.47
In Stock
Thermal Fuse
PartSelect #: PS4205213
Manufacturer #: DC47-00016A
This thermostat is a genuine OEM part and is manufacturer-approved for electric dryers. The thermostat is responsible for monitoring and maintaining the temperature inside the dryer during the drying ...
$27.36
In Stock
Thermal Fuse
PartSelect #: PS4205212
Manufacturer #: DC47-00015A
The thermal fuse measures the air temperature inside your dryer drum, and turns the heat on and off to maintain the optimal temperature during the drying cycle. If your dryer will not start, dry cloth...
$45.29
In Stock
Moisture Sensor
PartSelect #: PS4206812
Manufacturer #: DC61-02627A
This moisture sensor plate is specifically designed to fit with your Samsung dryer. It is made of stainless steel and measures approximately 5 inches long. It is designed to detect the amount of moist...
$16.07
In Stock
High Limit Thermostat - L260-50F
PartSelect #: PS4205217
Manufacturer #: DC47-00018A
The high limit thermostat is designed for use in your dryer. The function of this part is to make sure that your dryer does not get too hot. If your dryer is not regulating heat properly, you may need...
$47.40
In Stock
Dryer Assembly Bracket Thermostat
PartSelect #: PS4276292
Manufacturer #: DC96-00887C
This thermal cut-off fuse bracket assembly is a genuine replacement part supplied directly by Samsung for use in dryers. It is a safety component that is designed to protect the dryer from overheating...
$63.64
In Stock
Dryer Leveling Leg
PartSelect #: PS4206963
Manufacturer #: DC61-03128A
Leveling leg supports the dryer. Adjust the height of the leveling leg to make the dryer level.
$31.58
Special Order
Door Switch
PartSelect #: PS4210965
Manufacturer #: DC64-00828B
Introducing the Samsung Dryer Door Switch, a genuine, high-quality accessory for your Samsung dryer. This top-notch replacement part, also known as a door jamb switch, swiftly rectifies your broken or...
$55.29
In Stock
Common Symptoms of models starting with DVE50BG8300VA3
[Viewing 5 of 5]Not Heating
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The dryer turned on but the drum did not move when you pressed start even though It started it cycles.
I YouTube it and there’s a step by step process on how to do it, took maybe 30 mins. If I can so can you
Parts Used:
-
Christopher from SUGARLOAF, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
39 of 72 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer getting warm but turning off before clothes dry
Cleaned the sensors from inside the drum with alcohol and that did not work. Ordered two sensors. Lift top cover. Remove screws on each of the front side that secures front cover. Unplug door sensor and pull front cover towards you and lift at same time removing from frame. I own dogs and immediately noticed dog hair and surprisingly
... Read more
lint all over the place. Remove the screws from the lint trap. (Theres one you access from inside the drum.) Unplug your sensor wires. Remove lint trap. The sensors simply push in/out. While I was in there I removed the cover for the lint tube and cleaned it out good. Lint had started to gather around the fan. Reverse your process and your done. TIP: Keep your screws orderly as you unscrew them. If you have this problem, just a good cleaning of hair, lint, dirt may do the trick as it essentially packs around the plug of the sensors. I had already ordered my sensors so I just put them in. I took my time and cleaned good and it was about an hour. It could be done in 15-30 minutes easily.
Read less
Parts Used:
-
Eric from CHAMBERSBURG, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
11 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
New Purchase would not ever heat
Samsung had no servicers available, after over 3 months calling and sending photos and signing papers they sent a refund. Never any advice on repair from Samssung. Saw a video by JEFF OSTIROFF that lfor disassembly and location of heating parts. Gor $40 Samsug service manual that was rather useless. Disassembled and tested thermostat, T
... Read more
hermistor, and heat element. Appeared that HI-HEAT thermistor was open circuit all others OK. Sent for new one, arrived damaged insufficientlyb packed Tested original again out of appliance, tested OK. Got replacement for damaged thermistor and put it in, reassembled and IT WORKED! Notvsure if original thermistor was intermittant, or connection problem was the fault.
Read less
Parts Used:
-
Steve from SANDPOINT, ID
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!