Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a thermistor, also known as a dryer thermistor. The thermistor is attached to the blower housing, it will help regulate and oversee the temperature within the dryer. The most common symptom of...
This idler pulley assembly is sourced from the original manufacturer for use in dryers. The assembly includes the pulley wheel and bracket. It is found near the motor where it provides tension to the ...
The drum support roller and axle, which includes the roller shaft and mounting clips, is used in dryers. This part holds the drum as it rotates on the support wheels. When the roller begins to wear ou...
This thermostat is a genuine OEM part and is manufacturer-approved for electric dryers. The thermostat is responsible for monitoring and maintaining the temperature inside the dryer during the drying ...
The thermal fuse measures the air temperature inside your dryer drum, and turns the heat on and off to maintain the optimal temperature during the drying cycle. If your dryer will not start, dry cloth...
The high limit thermostat is designed for use in your dryer. The function of this part is to make sure that your dryer does not get too hot. If your dryer is not regulating heat properly, you may need...
This thermal cut-off fuse bracket assembly is a genuine replacement part supplied directly by Samsung for use in dryers. It is a safety component that is designed to protect the dryer from overheating...
Introducing the Samsung Dryer Door Switch, a genuine, high-quality accessory for your Samsung dryer. This top-notch replacement part, also known as a door jamb switch, swiftly rectifies your broken or...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tatjana
June 16, 2021
The dryer starts and spins two times and stops. We were told it’s the pcb main so we replaced it and it’s still doing the same thing. Any idea what this could be?
For model number DV56H9000EP
Hello Tatjana, Thank you for the question. This normally is caused by a bad motor or a bad main control board. If the board did not fix the issue, the motor may need to be replaced. We hope this helps!
The dryer is not heating also it runs even when the door is closed but not turned on.
For model number DV56H9000EP
Hello Doreen, thank you for your question. There could be few reasons your dryer is not drying your clothes. The number one reason is a blocked, bent, or broken vent. If you have checked and cleaned out your vent, we would suggest checking the Thermal Cut-Off Kit, part number PS4276292, Dryer High Limit Thermostat, part number PS4205217, and the Thermal Fuse, part number PS4205212. You can test those parts with a multi meter, and they should be reading 0 ohms to be working correctly. If those parts are fine, you should then go on to testing your heating element as well. Part number PS9606067. You can also test that with a multi meter, and it should be reading between 0 - 50 ohms. We hope this helps. For the dryer running while not on, it could either be the timer which is part of the control board, part number PS8763906 or the door switch, part number PS4210965. Good luck with your repair.
YouTube, YouTube, YouTube. I YouTubed many videos on how to take a dryer apart to reach the drum support roller and axle. After watching numerous videos, I settled on one that had my exact model of dryer. For my dryer, previous inputs said I needed two rollers to for my model. That is not the case. My model actually has 4 rollers, 2 in th
... Read moree front and two in the back. I ordered 2 initially but only needed 1 thankfully since only one roller was bad. Keep it simple stupid is how I got it done. Dryer's are pretty simple machines mechanically. Don't trash your noisy dryer. We bought ours in 2014 and it only recently started giving us issues. This is after 2 moves and being run daily for a family of 6. I'm glad I found partselect.com. They saved me a ton of money.
Watched a video on utube, how to repair my 16 month old steam dryer. The hardest part was laying on my belly holding the spring loaded tensioner and slipping the belt on around the blower housing. Only cost me $23. Winning!
Samsung had no servicers available, after over 3 months calling and sending photos and signing papers they sent a refund. Never any advice on repair from Samssung. Saw a video by JEFF OSTIROFF that lfor disassembly and location of heating parts. Gor $40 Samsug service manual that was rather useless. Disassembled and tested thermostat, T
... Read morehermistor, and heat element. Appeared that HI-HEAT thermistor was open circuit all others OK. Sent for new one, arrived damaged insufficientlyb packed Tested original again out of appliance, tested OK. Got replacement for damaged thermistor and put it in, reassembled and IT WORKED! Notvsure if original thermistor was intermittant, or connection problem was the fault.
