DV203AESXAC Samsung Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The dryer turned on but the drum did not move when you pressed start even though It started it cycles.
I YouTube it and there’s a step by step process on how to do it, took maybe 30 mins. If I can so can you
Parts Used:
-
Christopher from SUGARLOAF, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
38 of 71 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer stopped heating
I purchased wholesale heater element with sensors. Couple wires and bolts to attach. Trickiest part is disassembling the dryer to remove the old heating unit. You-tube it; it's gold.
Parts Used:
-
Mark from WEST SUNBURY, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating coil went ..
Dryer was pretty easy to disassemble. The video helped, especially when re-routing the drive belt. Would definitely but from Parts Select again!
Parts Used:
-
Peter from TROY, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dryer was running just fine in all areas except there was no heat. The vent line was not plugged.
I firstly over-ordered parts. The general guidance is check one part and replace if bad, then check the next, etc. I only wanted to do the disassembly once so I ordered all the parts which were involved with generating heat. Turned out the heater duct assembly came with the thermal fuse and thermistor already installed, in addition to the heating element. Once I had the parts, I watched the video which was identified in my parts order. Then I started disassembly. I put screws from each step into their own little container so there was no mixing them up. Everything went exactly as shown in the video, except for the front panel containing the control board. My dryer was slightly different, but still easy to get out. When I had the drum out, the heater duct assemble was easy to remove, one screw only. I transferred connecters from the old duct to the new one-at-a-time to make sure there were no mistakes, then installed the new one with the single screw. Re-assembly went quickly. I plugged it in and, with some hesitation, set it to a short timed cycle and started it. After a few minutes, I hit pause and stuck my hand in the drum and it was warm! The dryer has continued to work since. Repair successful!
Parts Used:
-
David from RENTON, WA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum stopped turning.
Followed the video on the website and finished it in a short time. Now it works like a new dryer.
Parts Used:
-
Dequince Atkinson from PLATTSBURG, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum don’t turn
-
Orlando from LAWRENCEVILLE, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original belt broke after nylon tension pulley bearing froze.
Thank you
partselect.com for a much better heavy duty belt than the original. Way over priced, but well worth it. After watching the video & following it step-by-step, I now have a perfectly running dryer. P.S. don't forget to plug back in the (3) wire harnesses. The entire experience was a great feeling of accomplishment. Thanks again partselect.com
partselect.com for a much better heavy duty belt than the original. Way over priced, but well worth it. After watching the video & following it step-by-step, I now have a perfectly running dryer. P.S. don't forget to plug back in the (3) wire harnesses. The entire experience was a great feeling of accomplishment. Thanks again partselect.com
Parts Used:
-
John m from GRAPEVIEW, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
high limit thermostat and heating element were bad.
I would like to direct the attention to PartSelect instead of my repair. They were awesome in helping me to get my parts. I had called, a few minutes after the deadline for overnight shipping, the gentleman helping me, pushed the order through and I got my parts the next day, allowing me to repair my dryer. I have ordered several parts, for several different appliances, (all Samsung) and PartSelect has always come through for me. Excellent Customer Service!!
P.S. Don't buy Samsung appliances unless you want to get good at repairing them!
P.S. Don't buy Samsung appliances unless you want to get good at repairing them!
Parts Used:
-
Paul from FIRESTONE, CO
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drier did not turn it was not the belt
I still had to take it apart there was a small sock stuck in the fan that blowes the lent out my wife left the lent filter out one time. Your video was a great help. I'm a mechanic and it was easy thanks Anthony Ratto Tulipbike82@aol.com
Parts Used:
-
Anthony from FLORAL PARK, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!