Models
>
DU7200XS5
DU7200XS5 Whirlpool Dishwasher - Overview
Sections of the DU7200XS5
[Viewing 6 of 6]
Manuals & Care Guides for DU7200XS5
Click to downloadKeep searches simple, eg. "belt" or "pump".
Rubber Washer
PartSelect #: PS11743934
Manufacturer #: WP717273
The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element...
$7.76
In Stock
Spring, Lid
PartSelect #: PS11744874
Manufacturer #: WP8066018
The dishwasher lid spring helps open the dispenser cover in the soap box when the control releases the latch. If your dishwasher does not dispense detergent, is broken and worn out, or the door is not...
$7.95
In Stock
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$7.76
In Stock
Door Spring Assembly with Adjusting Hook
PartSelect #: PS382742
Manufacturer #: 675611
This kit includes spring, retainer and protective tip. It is recommended to replace both springs at the same time.
$47.87
In Stock
Detergent Dispenser Cover Kit
PartSelect #: PS370872
Manufacturer #: 4387043
This kit also includes the lid hinge pin, spring, snap and latch.
$35.86
In Stock
Screw - 8-18 x 1/2
PartSelect #: PS11740645
Manufacturer #: WP302868
Sold Individually.
$7.84
In Stock
Screw
PartSelect #: PS11742721
Manufacturer #: WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
$7.91
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Lower Dishrack Kit
PartSelect #: PS2378335
Manufacturer #: W10311986
This kit comes with the wheels, bumpers, fold down tine and flexrow retainer.
$277.64
In Stock
Screw - 8-18 x 5/8
PartSelect #: PS11747050
Manufacturer #: WP9741232
Sold individually.
$7.95
In Stock
Drain Check Valve with O-Ring
PartSelect #: PS382661
Manufacturer #: 675238
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$49.77
In Stock
Questions And Answers for DU7200XS5
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the DU7200XS5
[Viewing 10 of 10]Will not dispense detergent
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher Not Draining
Ordered both drain & wash impeller kit and the drain check valve with o-ring. Decided to test the cheaper drain check valve first. Pulled dishwasher out from wall & adjacent cabinetry; removed drain hose from disposer and drained as much water as possible; "jacked" side of dishwasher to gain access to drain hose and drain check valve; us
... Read more
ed pliers to remove hose clamp; placed flat pan underneath to catch remaining water drainage; unscrewed drain check valve; tested under bathroom faucet--determined faulty; replaced with the new one, restored connections, reset dishwasher in proper location; voila--fixed! Plan to return the unneeded impeller kit.
Read less
Parts Used:
-
Lewis from Portsmouth, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
163 of 211 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Parts Used:
-
Michelle from Richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
64 of 125 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One of the door springs broke. These add a coutner balance to the door so it is easier to open and close
I have a Kenmore model that can either be totally installed under counter, left on casters or in my case installed permanently with the 'portable' covers still on. A model that is only for installation in a cabinet may be different.
Open door part way and flex the plastic hinge 'pins' on the kick plate out of the door itself. Once t ... Read more hese are out you can close the door and lay the kick plate down towards you. This will expose a spring that is attached to pins on either side of the kick plate and held in place by a rubber cap. Remove the cap, pull the loop of the spring off the pin, and repeat for the other side. At this point you can remove the kick plate and set aside out of the way.
There is a second plate behind the kick plate held in place by four screws. Remove the screws with a Phillips head screw driver or a 1/4 inch wrench or socket, then remove the plate and set aside.
Now you have exposed the frame rails that somewhat hide the springs, one on each side. If you are lucky, like I was, only one is broken so you can use the other as a guide. Also the installation drawings that came with the part were very helpful. The information supplied by Kenmore in the parts list was no help at all.
Follow the 'assembly' found in the kit to assemble the 3 parts of the spring. A this time you may want to open the door halfway then close it and reopen a couple of times and observe how the tail of the door hinge moves, this will show you where the spring is attached. The spring is mostly hidden behind the frame rails but the two connection points are visible with the help of a flashlight. If one of the springs in still connected, observe the two connection points, one on the tail of the door hinge (top of spring) and the other in a series of slots in the frame rail.
With the door closed, hold the spring assembly in one hand (easier said than done) and hook the top of the assembly over the hook on the door hinge. Let it hang down in place and slip the lower part of the assembly into one of the slots. Again if one of the springs is still in place just use the same location as before. If both springs are missing, use one of th slots in the middle.
Only one of my springs were broken but I installed new ones on both sides as cheap insurance against doing this again in a few months.
Step by step appears a bit complicated but the whole thing only took about 10 minutes.
Good luck.
Open door part way and flex the plastic hinge 'pins' on the kick plate out of the door itself. Once t ... Read more hese are out you can close the door and lay the kick plate down towards you. This will expose a spring that is attached to pins on either side of the kick plate and held in place by a rubber cap. Remove the cap, pull the loop of the spring off the pin, and repeat for the other side. At this point you can remove the kick plate and set aside out of the way.
There is a second plate behind the kick plate held in place by four screws. Remove the screws with a Phillips head screw driver or a 1/4 inch wrench or socket, then remove the plate and set aside.
Now you have exposed the frame rails that somewhat hide the springs, one on each side. If you are lucky, like I was, only one is broken so you can use the other as a guide. Also the installation drawings that came with the part were very helpful. The information supplied by Kenmore in the parts list was no help at all.
Follow the 'assembly' found in the kit to assemble the 3 parts of the spring. A this time you may want to open the door halfway then close it and reopen a couple of times and observe how the tail of the door hinge moves, this will show you where the spring is attached. The spring is mostly hidden behind the frame rails but the two connection points are visible with the help of a flashlight. If one of the springs in still connected, observe the two connection points, one on the tail of the door hinge (top of spring) and the other in a series of slots in the frame rail.
With the door closed, hold the spring assembly in one hand (easier said than done) and hook the top of the assembly over the hook on the door hinge. Let it hang down in place and slip the lower part of the assembly into one of the slots. Again if one of the springs is still in place just use the same location as before. If both springs are missing, use one of th slots in the middle.
Only one of my springs were broken but I installed new ones on both sides as cheap insurance against doing this again in a few months.
Step by step appears a bit complicated but the whole thing only took about 10 minutes.
Good luck.
Read less
Parts Used:
-
Ruthann from Auburn, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
24 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!