Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DU1014XTXQ5

DU1014XTXQ5 Whirlpool Dishwasher - Overview

Get Parts and Repair Help for DU1014XTXQ5

If you know the dishwasher repair part you need, you can browse the list of all parts on the DU1014XTXQ5, or you can search by name or part description. You can also find your part by where it is located on the DU1014XTXQ5 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for DU1014XTXQ5 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$37.84

Heating Element

This heating element is designed to monitor and control the heat of the water that enters the dishwasher. It is located at the bottom of the dishwasher. If your dishwasher is not d...

Order within the next 3 hrs and your part ships today!
$55.31

Door Gasket with Strike - Black

This product contains both the door gasket and the door strike. The function of the door gasket on your dishwasher is to provide a seal between the tub and the door. The door strike serves as a mechanical actuator for door switch operation and provides door tension for a proper seal. If you notice that your dishwasher is leaking, the door will not latch properly, or it is not cleaning dishes properly, you may need to replace the door gasket. This repair is as simple as removing the old gasket from the channel on the edge of the dishwasher tub, and replacing it with the new one. This product is made of black rubber.

Order within the next 3 hrs and your part ships today!
$6.12

Rack Track Stop

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes ...

Order within the next 3 hrs and your part ships today!
$11.43

Mounting Bracket

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

Order within the next 3 hrs and your part ships today!
$16.26

Upper Adjustable Rack Wheel - 2 Positions

Sold individually.

Order within the next 3 hrs and your part ships today!
$25.95

Chopper Assembly

This chopper assembly, or dishwasher drain food chopper, chops food particles into small pieces to prevent the dishwasher pump from clogging. If your dishwasher is making grinding, rattling, or humming noises, replacing this part may solve the issue. Other symptoms include not draining, low water pressure, chopper not working, or the dishes not being cleaned. The tools needed for this repair project are a #15 torque spit, #20 torque spit, small flat blade screwdriver, and needle nose pliers. Make sure to unplug your dishwasher from the power source before beginning installation. Refer to the manual provided by the manufacturer for further instructions.

Order within the next 3 hrs and your part ships today!
$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where...

Order within the next 3 hrs and your part ships today!
$65.70

Drain Pump - 120V 60Hz

This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.

Order within the next 3 hrs and your part ships today!
$7.00

Spray Arm Seal

This seal is located between the spray arm and the water feed tube.

Order within the next 3 hrs and your part ships today!
$4.40

Friction Sleeve

This part helps to keep your door quiet when it opens and closes.

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishes on top rack of dishwasher were not being cleaned.

  • Customer: Bill from North Richland Hills, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 304 of 324 people found this instruction helpful
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to th... read more

dishwasher not draining after wash cycle

  • Customer: Andrew from Alexandria, VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 308 of 343 people found this instruction helpful
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
... read more

Heater element broken.

  • Customer: Dennis from Sedro Woolley, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 131 of 142 people found this instruction helpful
Step 1: Remove the screws in the bottom of the countertop.

Step 2: Remove the screws holding the bottom kickplate.

Step 3: Loosen leveling legs.

Step 4: Pull dishwasher out of hole.

Step 5: Unlplug dishwasher.

Step 6: Disconnect wires from bottom of element in back.

Step 7: Remove plastic nuts... read more