Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DH30G0

DH30G0 Whirlpool Dehumidifier - Overview

Get Parts and Repair Help for DH30G0

If you know the dehumidifier repair part you need, you can browse the list of all parts on the DH30G0, or you can search by name or part description. You can also find your part by where it is located on the DH30G0 by selecting a section below. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the DH30G0

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.96

Single Hex Head Screw

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

Order within the next 7 hrs and your part ships today!
$4.12

Float

If the bucket is full indicator on your dehumidifier is on but the bucket is empty, you may have a problem with the float. If you notice that the float is warped or damaged, it should be replaced. This device is located near the bucket and prevents the dehumidifier from overflowing. You will need to open up the dehumidifier to complete this repair. This product is approximately 4 inches in length. Many of our customers have rated this repair as easy. To complete the repair simply remove the clips that hold the float in place, attach the new float, and replace the clips.

Order within the next 7 hrs and your part ships today!
$69.19

Bucket and Float Kit

This bucket and float kit, also known as water tank assembly, is for a dehumidifier is 14.5 inches long and 8.5 inches wide. The water tank extracts, traps, and contains the moistu...

Order within the next 7 hrs and your part ships today!
$36.98

Humidistat Control

The humidistat control, used in dehumidifiers, switches the dehumidifier on and off automatically to maintain humidity. If the switch does not work, the humidifier will not maintain the temperature properly. For this repair, screwdrivers are the only tools needed. First remove the knob and the screws from the top. Pry back the plastic retainers on one side of the old humidistat and remove wires before installing the new part and reattaching the two wires that connect to it. Remember to unplug the humidifier from the power source before installation.

Order within the next 7 hrs and your part ships today!
$4.88

TIE-WIRE

Order within the next 7 hrs and your part ships today!
$4.69

Float Clip

The float clip works in a humidifier to ensure the float functions properly. The float is located near the humidifier bucket and monitors the water level as it rises and the clip keeps it in place. The float makes sure the water level is balanced and does not over flow. This float triggers the flow switch to shut off. If there is a defect with the clip, it can be a safety hazard as it might not be able to detect and stop an overflow. Make sure to unplug the dehumidifier from the power source before starting this replacement project as a safety precaution.

Order within the next 7 hrs and your part ships today!
$58.12

Bucket Water Level Switch

This part is for your dehumidifier. The bucket water level switch is used to prevent water overflow when the bucket is full. You will not be able to tell if the switch has failed j...

Order within the next 7 hrs and your part ships today!

Castor

Also known as wheel or roller. This part is sold individually.

PAN-DRAIN

$27.12

CORD-POWER

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The Origional Humidistat Quit Working

  • Customer: James from Silver Bay, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 13 people found this instruction helpful
The knob one turns to set the humidity level was removed. The two screws holding the top on were removed. The top was lifted and swung to the side. After noting which of the two wires went where on the humidistat the wires were removed. Small flat screwdrivers were used to pry back the plastic retainers on one side of the original failed humidistat. The... read more

the humidity control broke

  • Customer: larry from tampa, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 14 people found this instruction helpful
Taking the case apart and replacing the control unit was a piece of cake. And the part arrived the very day after I ordered it. read more

the dehumidifier was not shutting off when water level was full

  • Customer: Steven from Owings Mills, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 6 people found this instruction helpful
replaced a piece of the plastic at the top of the bucket that seems to be the water gauge. this seems to be fixed. we are very happy read more