DF240140 (46) Gaggenau Dishwasher - Instructions

Here are the steps you need to take to do the job properly:

1. turn off electrical circuit breaker to the dishwasher
2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed.
3. unplug the wiring harness to the detergent/rinse aid dispenser
4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser.
5. the unit will pop out toward the inside of the dishwasher
6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in.
7. re-attach the wiring harness
8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job.
9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks.
10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.

I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .

I removed the old gasket easily, it pulled right out. I spent a few minutes cleaning the gunk out from the seam using a standard kitchen cleaner (it was gross and I had to do it multiple times). Tip: pay attention to the shape of the gasket and which side faces in vs. out when pulling out the old one. Also, for reference, take a photo of the old gasket and how it's positioned before pulling it out. Then, simply start at the bottom (either side) and insert the new gasket. Work your way up, over and down the other side. If it's facing the right way it'll go in very easily, if not is will be very difficult—this is how you'll know. After installation, run your dishwasher empty for a full cycle (with towel underneath the door) and check back frequently during the cycle. If there are no leaks you're done. This was the fastest, easiest way to attempt to fix a leaky door and eliminate the gasket as the problem (which it did!) If the machine still leaks the issue is likely something bigger.

Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.

Ordered the complete soap /rinse additive unit.nturn power off. Take the peripherical screws to remove the front of the door. Slide the door down and off. Unplug wires 2 places. Use a screwdrive to pry the tabs allowing the unit to come out

Important. Add a little Vaseline to the seal on the new part. Press it in until the tabs engage. Reconnect wiring and replace door front. Turn power on Job complete.

Use screwdriver to gently wedge the side of the dispenser body apart enough to pop out the old kid, then insert the new kid in it's place.

My husband spent minimal time and maybe just screwdriver for repair of replacement part.
Your company was great to work with.
Thank you!

Use a screwdriver flat blade to pry up one edge of closed lid. Put one side of lid into hinge and snapped other side into place. Very easy.

I took out the old filter and replaced it with the filter I had ordered. Very easy and not necessary to call a repairman.

Followed the video on your site and it was an easy install with no more leakage.

I have granite countertops and one of the hold down brackets broke to wood cabinet side mount. Easy and fast repair to remove old brackets, pull out dishwasher, and I replaced both brackets with new, and new wood screws. New installation looks better than original done 18 years ago. Very easy to do and saved a lot of money if I had an appliance repair company do it.

I snapped the part in and voila!

Replaced ‘sump’ housing , seal was leaking on it- replaced inop float on water level warning system switch, and switch itself as well- replaced drain pump motor attached to sump- replaced o-ring seal at water sprayer inlet valve- replaced water inlet plastic assemble on side of dishwasher- replaced drain hose out of sump assembly.

Used YouTube video to understand repair- this is an involved repair in time and complexity- dishwasher eventually gets turned upside down once removed and stripped down, to remove the white plastic water pan , which then allows access to the guts of all the above parts- some critical seals only come with new assemblies, so you are buying that new part to get a new seal and ensure no new leaks from what you took apart.

Unscrewed the old piece screwed in the new

The perfect replacement part. Plug and play.