Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DE2000D-W1

DE2000D-W1 Frigidaire Dryer - Overview

Get Parts and Repair Help for DE2000D-W1

If you know the dryer repair part you need, you can browse the list of all parts on the DE2000D-W1, or you can search by name or part description. You can also find your part by where it is located on the DE2000D-W1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DE2000D-W1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.41

Drum Support Bearing

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear b...

$2.94

Door Latch Kit

The door latch is designed to keep your dryer door closed, even during the drying cycle. If your dryer door will not stay closed, the drying cycle might not start, or it could stop suddenly. If you notice this is happening, check the latch itself for any physical damage. If you notice that it is damaged, the latch should be replaced straight away. This genuine OEM part is compatible with different brands and models, so check to make sure it will properly fit yours before ordering. This door latch kit comes with both the strike and the catch. We suggest replacing both parts of the door latch at the same time.

$29.32

Door Catch

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, w...

$10.64

Bearing Bracket

This OEM drum bearing bracket holds and supports the drum bearing in your clothes dryer. The bracket is located behind the dryer drum. Common symptoms that are linked to faulty or damaged drum bearing brackets include: the dryer will not start, will not tumble, or the dryer is making loud squeaking or grinding sounds. If there is an issue with the bearing bracket, it will need to be replaced. Replacing the bracket has been listed as a very easy to easy repair by many of our customers. Remember to disconnect the power to your dryer before beginning this repair.

$7.51

Flat Style Belt

This is a flat style ridgeless dryer belt.

$8.87

Grounding Ball

This grounding ball is used in dryers and works to prevent friction in the rear bearing when the drum rotates. If your dryer is making a squealing, loud, banging noise or will not operate, it is best to replace it to solve the problem. To repair, first remove the main top and remove the strap at the back of the dryer to lift the lid. Next, remove the two wire harnesses and Phillip screws on the sides that connect to the front panel. Now that you have access to the inside of the dryer, refer to the manual for further instructions by following the manual provided by the manufacturer.

$12.84

Idler Pulley Assembly

Use this idler pulley assembly with gas or electric clothes dryer that has a flat dryer belt. ***Please NOTE: This part has been redesigned by the manufacturer and may not fit you...

$31.04

High Temperature Adhesive

This high temperature adhesive is used for installing felt and rubber seals on dryers. The tube contains 1 ounce of product. This adhesive is made to withstand extremely hot temperatures. Before applying the adhesive, ensure that the area is completely clean from any debris and is dry. You may wish to use small clamps to hold the material in place while it dries. If the felt has come loose or broken apart, this may cause your dryer to make loud noise, indicating that new felt or rubber needs to be glued into place. Use gloves to apply glue.

$8.30

Grounding Ball Clip

This grounding ball clip is made of metal. Sold individually.

$36.35

Seal

Adhesive is sold separately.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Catch broke, door wouldn't stay closed.

  • Customer: Dianne from Kansas City, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 62 of 66 people found this instruction helpful
Used a screwdriver to pop out broken piece. Used pliers to snap in new one. read more

Terminal Block Melts when power cord connector is left loose by install crew.

  • Customer: Arthur from Grand Prairie, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 43 of 59 people found this instruction helpful
1) Removed Top Dryer Cover (pushed 2 compression clips on front side 1" from top and 2" in from each side) to gain access to terminal block in rear.
2) Removed 2 screws over terminal block cover and 2 screws holding bad terminal block in place. Removed 3 screws holding bad power cord,
3) Removed good terminal connectors from bad terminal block a... read more

Torn Lint Screen

  • Customer: David from Birmingham, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 33 of 39 people found this instruction helpful
Actually, I didn't install the frame. I only needed the lint screen. So EASY, obviously... I just placed the new lint screen in the old frame. We had been messing around with the torn lint screen for more than one year. Installing the new part was as easy as ordering from PartSelect. read more