Models
>
DE16CM
DE16CM Amana Dryer - Overview
Sections of the DE16CM
[Viewing 10 of 10]Keep searches simple, eg. "belt" or "pump".
Drum Roller Shaft Washer
PartSelect #: PS11740748
Manufacturer #: WP312535
If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold indivi...
$13.79
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Rubber Foot Pad
PartSelect #: PS11738859
Manufacturer #: WP210684
The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is ju...
$15.28
In Stock
Cycling Thermostat - Limit 135/155
PartSelect #: PS11743793
Manufacturer #: WP694674
Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature within the dryer. This particular cycling thermostat can be adjusted between 135 and 155 de...
$57.32
In Stock
Adjustable Leveling Leg
PartSelect #: PS2021026
Manufacturer #: 22003428
If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs ...
$18.47
In Stock
Lower Dishrack Kit
PartSelect #: PS2378335
Manufacturer #: W10311986
This kit comes with the wheels, bumpers, fold down tine and flexrow retainer.
$277.64
In Stock
Heating Element Terminal & Insulator Kit
PartSelect #: PS1760665
Manufacturer #: Y304596
This kit comes with two ceramic insulators.
$24.41
In Stock
Hex Nut
PartSelect #: PS11738304
Manufacturer #: WP112432
This 10-32-inch hex nut works with multiple appliances in your home as a fastener. This specific model is sold individually. Hex nuts usually have 6 even sides and together they are used with bolts an...
$8.04
In Stock
Lint Filter
PartSelect #: PS2028956
Manufacturer #: 300838
This filter collects lint as it passes through the dryer vent.
No Longer Available
Motor Clip
PartSelect #: PS11757442
Manufacturer #: WPY015825
This motor clip is an original manufacturer replacement clip used to secure the motor in your home appliances. It holds the motor firmly to its housing to prevent shaking and potential damage while th...
$21.62
In Stock
Questions And Answers for DE16CM
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the DE16CM
[Viewing 2 of 2]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer wouldn't heat
Since the heating coil is right behind the front door I had to remove all panels starting with the back one to get to it. The back has a lot of tech screws that I removed with the nut driver. The side panels were removed with a phillips screwdriver. The top is held in place with the other panels. The base was shifted away from the fro
... Read more
nt and I released the heating coil case with 4 screws in the front and was able to pull it out of the top to replace it. I cut the old one out with wire cutters and snaked the new one through the ceramic insulators. I was careful not to touch the new one without gloves because the oil from your hands can burn them out more quickly. I screwed the new ones to the contact points while trying not to stretch it too much. I vacuumed the whole dryer out before putting it back together.
Read less
Parts Used:
-
Edith from Grove City, OH
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
59 of 68 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stripped leveler screw making impossible to level my washer
Put blocks under the washer where the leveling leg was needed and screwed the part into the washer. Then it was just a matter of moving the washer into place and leveling. Pretty easy.
Parts Used:
-
Rebecca from Wylie, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
21 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Temperature setting not working
Took off back cover, thermostat was easily identified because of photos I've seen on website. Took 2 connectors off, removed 2 screws and removed old thermostat. That was pretty much it!
NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use ... Read more the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.
NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use ... Read more the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.
Read less
Parts Used:
-
Robert from Buffalo, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
17 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!