Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for ...
This original equipment manufacturer Drum Bearing Slide is a plastic, green, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if...
This timer knob is used to set the dryer cycle by advancing the timer. The plastic can become brittle with age and crack where it attaches to the timer shaft. You will need to replace this part if it ...
This light bulb, also known as a drum lamp, illuminates and lights up the dryer drum when the door is open. If the light bulb in the dryer is burnt out or lighting is inconsistent, replacing it can so...
This lint chute assembly is a genuine replacement component designed for GE and Hotpoint dryers. It plays a critical role in directing exhaust airflow from the dryer drum to the blower wheel, ensuring...
This rear drum bearing sleeve is a critical support component located at the back of the dryer drum, designed to reduce friction and ensure smooth rotation during operation. As the drum spins, the sle...
This authentic OEM rear bearing O-ring is designed for use with GE dryers. It helps secure the drum rear bearing onto the drum shaft, playing a key role in maintaining smooth and quiet dryer operation...
This part is the replacement high-limit thermostat or safety thermostat for your dryer. The high-limit thermostat is found on the upper right-hand side of the heater housing, and it cuts off power to ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
September 29, 2021
How to disassemble to obtain slide to replace?
For model number DBXR463EB0WW
Hi Robert,
Thank you for your question. Here is a link to one of our YouTube videos that you may reference on how to install the slides. The dryer in the video may appear different from yours, but it will give you a general idea on how to install the part. We hope this helps! Good luck with the repair!
Hi Judy, thank you for reaching out. We have searched and attached a video that will help you replace the lint chute assembly. We hope this video helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lisa
April 10, 2024
How do you remove and replace the Drive belt?
The dryer starts to turn on, but will not spin.
For model number DBXR463EB0WW
Hello Lisa, thank you for contacting us. We have attached a relevant video to remove and replace the drive belt. The video may not be of the same exact model but will help you with the process. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Alexander
December 5, 2024
I have been troubleshooting my dryer on why it won't start. When I turn the start knob I hear the timer start. I checked the door switch and it's working properly as well as checking the start knob. Could I potentially have an issue with the timer selector not working properly or should I be looking elsewhere.
For model number DBXR463EB0WW
Hi Alexander,
Thank you for your question. If the door and start switches are working normally, we would recommend checking the timer and the drive motor. Before removing and checking these parts for continuity with a multimeter on the Rx1 setting, unplug the dryer from the electrical outlet. For the motor, you should receive a reading zero or close to zero. Place one probe on the bare metal housing of the motor, and place the other probe on each terminal one at a time to check the ground connection. You should not receive any reading from this test. If your motor fails either of the tests above, you will need a replacement motor. For the timer, you should receive a reading of 2000-3000 ohms. If you receive any other reading, you will need a replacement timer. We hope this helps!
how does the dryer keep running after you stop it?
For model number DBXR463EB0WW
Hello Willie, thank you for your query. We would recommend checking the timer, part number PS267932, to fix the issue. This timer is used to control the unit's cycles by regulating the length of time that power is directed to each setting. Good luck with your repair!
First of all, unplug the dryer. I removed the two screws on the front of the cabinet to remove the top. I then took out the screws to remove the dial panel. Release the belt for the drum through the access hole in the rear of the dryer. Remove the front cover and pull the drum assembly out.
Remove the element disc from the
... Read more rear of the housing, take note of the the wireing placement. Replace disc and reverse order of disassembly.
This job was easy for me as I am a tinkerer by nature. The hardest part of the whole job was waiting on the part, which by the way was ordered on a Sunday evening and I had the replacement in my hands and back in the dryer running by 1:00 PM on the following Tuesday!
I book marked this website and WILL refer it to others who simply need a repair, not a costly new appliance!
I pried out the remaining pieces of the handle out of the door with a screwdriver. When the new part arrived, I snapped it into place and it was done. It fit perfectly.
