Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CSP2760KQ1

CSP2760KQ1 Whirlpool Dryer - Overview

Get Parts and Repair Help for CSP2760KQ1

If you know the dryer repair part you need, you can browse the list of all parts on the CSP2760KQ1, or you can search by name or part description. You can also find your part by where it is located on the CSP2760KQ1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for CSP2760KQ1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.81

Door Switch - 3 Wire

A door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open. This part may need to be replaced if you find that the dryer is not...

$3.56

Door Catch Kit

This is a door catch kit, and it is designed for use with your dryer. On your appliance you will find both a strike and a catch, these two parts work together to keep your dryer door closed. This kit includes two strikes, three catches, and a set of instructions. Each of the door catches included have a different tension. Make sure you use the one that matches the existing catch on your appliance. All three of these are color-coded, and have a number on the back. The instruction sheet will tell you which catch you need to use for your specific model type.

$26.37

Lint Filter

This filter collects lint as it passes through the dryer vent.

$20.42

Idler Pulley

The idler pulley with tri-ring and gasket, also known as a dryer belt tension pulley wheel, is used in dryers. This part maintains the right amount of tension for the belt to rotate the drum. This effectively spins the drum. If your dryer is experiencing any of the following symptoms, it is best to replace this part: not rotating, does not start, making squealing noises when it is in use, or it does not tumble properly. For this repair project, the tools needed are a Phillips screwdriver, 1/4 inch nut driver, putty knife, small flat blade screw driver, and needle nose pliers. Refer to the manual provided by the manufacturer for installation instructions.

$42.43

Dryer Repair Kit

This kit comes with one multi rib belt, four drum support rollers, one idler assembly, nine tri rings and one washer.

$13.09

Drive Belt

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide.

$10.34

Drum Support Roller

This is a drum support roller for a dryer. The part includes the drum roller only and does not include the tri rings. Although most dryers require two drum support rollers, this pa...

$5.76

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

$4.94

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

$41.80

High Limit Thermostat and Thermal Fuse Kit

Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than the thermostat. Once it trips, it has to be replaced.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door switch was bad

  • Customer: pat from lisbon,, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 924 of 947 people found this instruction helpful
i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service read more

Door Catch part had fallen out,/ was missing

  • Customer: Terri from Saint Augustine, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 614 of 641 people found this instruction helpful
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source. read more

Dryer Would Not Turn Off With Door Open

  • Customer: RICHARD from NORCROSS, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 512 of 519 people found this instruction helpful
Pryed dryer top open and opened front door. . Unscrewed the 2 retaining screws. Pulled old switch from the wiring harness. Put new switch in place and replaced the retaining screws. Put new switch wire plug into the wiring harness. Before closing top, checked door switch function with dryer on. Dryer cut off when door open and when closed dryer ... read more