Models
>
CS-345
CS-345 Echo Chainsaw - Overview
Models starting with CS-345
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Spark Plug Bpm-8Y
PartSelect #: PS9263506
Manufacturer #: 15901019830
This Spark Plug Bpm-8y is a silver and white OEM part. Made of steel and ceramic it is individually sold, and is an electrical part. It is installed with a spark plug socket and is rated as Easy to in...
$3.99
In Stock
Fuel Filter
PartSelect #: PS11826311
Manufacturer #: A369000480
This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers.
Th...
$5.36
In Stock
Fuel Tank Vent
PartSelect #: PS9183121
Manufacturer #: A356000031
This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Ma...
$7.63
In Stock
Vent Tube
PartSelect #: PS9322952
Manufacturer #: V471001200
This is the replacement vent tube for your outdoor power equipment. It is made of black plastic and is approximately 3 inches long and ¼ inch thick. The vent tube allows air into the fuel tank so that...
No Longer Available
Stud
PartSelect #: PS9237151
Manufacturer #: V224000031
This part is the replacement stud for your chainsaw. It is approximately 1 ¼ inches long and is black in color. The stud secures the chain bar to the chainsaw. It the stud is damaged or missing, it ca...
$4.99
In Stock
Purge Bulb
PartSelect #: PS8857246
Manufacturer #: 12318139130
This OEM replacement part is used to pump fuel from the tank to the carburetor in order to start the engine. It may also be referred to as a Primer Bulb. It is made of durable black plastic and is sol...
$6.81
In Stock
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bulb was worn out and broken open
The unit is a press fit. To remove the old one required breaking the plastic compression tabs that hold it in place. That was simple enough. Replacing requires lining up in the correct position to meet the inner hose. Then push it in. The compression tabs on the replacement click in and hold.in place.
Parts Used:
-
Richard from SPRING HILL, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
worn out paddles and scrapper blade
I followed the instructions on Youtube, but I used an Impact drill and ratchet set. The hardest part is assembling the screw on the lower part of the paddle. It helps if you have your snow blower against a wall or something else so that it can not move b/c you will need some strength to push the screw threw the pre-drilled hole to the 10
... Read more
mm nut. I used a vise grip to hold the nut do to the lack of space and with my impact driver started to thread the screw to the nut. This part took about 1 min on one side and 10 minutes on the other side. I guess I got lucky the first time. Changing the scraper blade took about 4 minutes start to finish. It will help if you have needle nose pliers to remove and reattach the spring on each side. The instruction on you tube were very helpful. Hope you find this information helpful.
Read less
Parts Used:
-
Sam from GAITHERSBURG, MD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!