CEA2D2 Crosley Range - Instructions

Donna from Dallas, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

473 of 481 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip bowls needed to be replaced

took old bowls out, put new bowls in, took a coffee break

Parts Used:

John from Chester, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

455 of 546 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Stove top element not working due to bad receptacle.

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

Parts Used:

Richard from Carthage, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

194 of 214 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old drip pans stained

Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!

Parts Used:

Linda from Atlanta, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

218 of 427 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

one of my burners would only work half the time, and you had to wobble it to make it work

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new element using the wire caps, and finished bye rescrewing the element backinto place.

Parts Used:

cindy from Sebeka, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

138 of 265 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

We needed new drip pans and no one carried the model we needed

we removed the old pans after first removing the electric heating element and simply inserted tne new pans

Parts Used:

sylvia from ventnor city, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

67 of 71 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced drip bowls in stove

Took out the old drip bowls and replaced with new bowls.

Parts Used:

Liza from College Point, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

71 of 134 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rented appartment in which none of the drain pans were the proper size making it very difficult to cook

I removed the element and then the drain pan and replaced with the new correct pans. I replaced the element and all was well.

Parts Used:

Grace Mary from Canton, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

67 of 131 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner was out but the burner coil worked on onother burner

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

Parts Used:

Richard from Orange, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

10 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Purchased home but stove had no broiler pan.

Purchased 2 piece broiler pan from this site

Parts Used:

2 Piece Broiler Pan

Raymond from BLOOMINGTON, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

16 of 31 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner receptacle burned out

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

Parts Used:

Michael from N. Haverhill, NH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven would not heat

For an oven this old, and not to mention a somewhat unique size, I did not expect to find any replacement parts. I removed the screws from the back of the oven; cut the wires; installed new high temp connectors by crimping them on to the wires; connected and installed the new bake element. The fit was practically identical!

Parts Used:

Bake Element

Luis Ruiz from Duluth, GA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

7 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

electric coils would not stay flat as drip pans were incorrect fit

replaced drip pans with correct type

Parts Used:

Janet from Philadelphia, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Store-bought drip bowls wouldn't fit.

My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

Parts Used:

Sharon from Yacolt, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The heating element socket had crumbled with age.

Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.

Parts Used: