CCG2423S Jenn-Air Cooktop - Overview
Sections of the CCG2423S
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Dryer Screw
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.47
In Stock
Range Surface Burner Knob
PartSelect #: PS11743880
Manufacturer #: WP71002372
This burner knob is two inches in diameter. It is a black knob with a white indicator dot. This knob is made entirely of plastic.
$24.67
In Stock
Spark Igniter
PartSelect #: PS11744544
Manufacturer #: WP7432P109-60
This part creates the spark that lights the gas and starts the burners.
$56.33
In Stock
Range Burner Pan Seal Large
PartSelect #: PS11743854
Manufacturer #: WP71001670
This large pan seal is approximately eight inches in diameter. It is all black in color and it is made entirely of rubber.
No Longer Available
Range Burner Pan Seal Small
PartSelect #: PS11743853
Manufacturer #: WP71001669
This small burner pan seal is approximately six inches in diameter. It is all black in color and is made entirely of rubber.
$63.64
Special Order
Range Mounting Nut
PartSelect #: PS11743922
Manufacturer #: WP7103P178-60
Sold individually.
$9.62
Special Order
REGULATOR
PartSelect #: PS12074765
Manufacturer #: W11106948
This pressure regulator is three inches long. It is made of metal, but has a blue plastic plug on each end. This regulator sits below a gas range's control panel.
$133.26
On Order
Valve Screw
PartSelect #: PS3651486
Manufacturer #: W10491986
Part might differ in appearance, but functions same as original. Sold individually.
No Longer Available
Common Symptoms of the CCG2423S
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
stove top gas burner ignitor only flicks but does not light burner
If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we h
... Read more
ad to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.
Read less
Parts Used:
-
Marlene from Dana Point, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
12 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Spark function just quit working.
The instructions on the website made it real easy to remove & Replace with a new module. Thanks for your Part & Install instructions.
Parts Used:
-
Gary from CARSON CITY, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
As soon as the parts arived it tooks only 1 1/2 hours to get everything fixed
-
Robert from Pleasanton, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
2 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!