Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CAM2761KQ0

CAM2761KQ0 Whirlpool Washer - Overview

Get Parts and Repair Help for CAM2761KQ0

If you know the washer repair part you need, you can browse the list of all parts on the CAM2761KQ0, or you can search by name or part description. You can also find your part by where it is located on the CAM2761KQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for CAM2761KQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.84

Suspension Spring

The suspension is meant to support the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or perhaps has stretched ou...

$28.33

Direct Drive Water Pump

This direct drive water pump, also known as washing machine drain pump or washer drain pump, is manufactured for washing machines that do not have belts. This is a genuine Whirlpool part with two ports for water to pass through, a large one and a smaller one, that will need replacing if the washer has a defective pump. Tools needed are slip joint pliers, a flat blade screw driver, and a putty knife. Sandpaper might also be needed to remove rust from internal parts to install the new pump. The washer will have to be disconnected from power and tilted on its back.

$44.29

Clutch Assembly

A clutch assembly is found in your washing machine and is responsible for spinning the basket during the spin cycle. A worn-down clutch can lead to a slower spin which can lead to ...

$30.63

Water Inlet Valve with Mounting Bracket

The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.

$3.56

Tub Spring

This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of th...

$4.63

Screw & Washer (5/16-24 x 1)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$12.08

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

$6.88

Leveling Spring

This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.

$4.28

GASKET

This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edg...

$2.81

Foot, Front - Single

The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water pump leaking when machine used.

  • Customer: Tom from Granby, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 535 of 564 people found this instruction helpful
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary access to the pump. ... read more

spin cycle did not engage

  • Customer: Andrew from SLC, UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 392 of 416 people found this instruction helpful
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase... read more

washing machine is slow to fill with cold water

  • Customer: Roy from Nash, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 255 of 277 people found this instruction helpful
My washing machine became slower and slower to fill over the past several months. It also made a loud squeeling noise during fill-up (all this was on the cold water side only). I removed the old water inlet valve and tore it down, expecting to find corrosion or trash that was blocking the valve from opening completely. Turned out to that the rubber diaphr... read more