Models
>
AK2H30HR
AK2H30HR (P1119901S) Amana Cooktop - Overview
Sections of the AK2H30HR
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Control Knob
PartSelect #: PS11747844
Manufacturer #: WPD8598001
This black control knob is a little over two inches in diameter.
$39.24
In Stock
Control Hole Cover
PartSelect #: PS2108389
Manufacturer #: B5037602
This control hole cover sits under the control knob.
No Longer Available
Radiant Surface Burner Element 1500W
PartSelect #: PS11764909
Manufacturer #: W10823699
This surface element is made for under glass set-ups and supplies the heat to a cooking area on top of the range. It has an outside diameter of approximately 7 inches (1500 watts), and is a genuine OE...
$106.72
In Stock
Screw
PartSelect #: PS11742713
Manufacturer #: WP488234
This screw is sold individually.
Size: 8-32 x 1/4 inch.
$9.13
Special Order
Dual Burner Element with Limiter
PartSelect #: PS11764904
Manufacturer #: W10823694
$212.59
In Stock
Control Knob
PartSelect #: PS2122310
Manufacturer #: D8598005
Sold Individually. This knob accepts a double-flat shaft.
No Longer Available
Surface Burner Control Switch
PartSelect #: PS17307
Manufacturer #: 0309550
This dual surface burner infinite control switch is just under three inches long. Using 240 volts, this switch will operate at 15 amps.
No Longer Available
Questions And Answers for AK2H30HR
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the AK2H30HR
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replacement of burner control switch
1. Open the circuit breaker feeding the range. Turn all range control switches ON to establish that there is no power. Remove all knobs.
2. Get under the range and remove the 2 hex-head screws securing the flex conduit to the bottom panel. Then remove the 20 hex-head screws securing the panel to the range. Lower the panel and place a ... Read more side, and then after checking for no voltage disconnect the red and black incoming wires by pulling on the spade connectors. Make sure you mark which wire went where.
3. From below apply pressure to the range frame to free the top surface gasket from collected food debris, then from above lift our the range and place upside down on a towel. Support the range with wooden blocks so that the unit is not resting on the knob shafts.
4. The control switches are all mounted on a common bracket with two screws for each switch. The first task is to remove two screws on each side holding the bracket to the frame, and then two wire harnesses on each side. Then gently move the bracket and rotate it sidewards so you have access to the screws holding down the switches.
5. Remove the defective switch leaving all the wires still connected.
6. Install the new switch and transfer the wires from the defective switch.
7. You're done, now restore everything in reverse, just make sure all wires move freely and not pinched.
2. Get under the range and remove the 2 hex-head screws securing the flex conduit to the bottom panel. Then remove the 20 hex-head screws securing the panel to the range. Lower the panel and place a ... Read more side, and then after checking for no voltage disconnect the red and black incoming wires by pulling on the spade connectors. Make sure you mark which wire went where.
3. From below apply pressure to the range frame to free the top surface gasket from collected food debris, then from above lift our the range and place upside down on a towel. Support the range with wooden blocks so that the unit is not resting on the knob shafts.
4. The control switches are all mounted on a common bracket with two screws for each switch. The first task is to remove two screws on each side holding the bracket to the frame, and then two wire harnesses on each side. Then gently move the bracket and rotate it sidewards so you have access to the screws holding down the switches.
5. Remove the defective switch leaving all the wires still connected.
6. Install the new switch and transfer the wires from the defective switch.
7. You're done, now restore everything in reverse, just make sure all wires move freely and not pinched.
Read less
Parts Used:
-
Farouk from Sudbury, MA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element not heating
This was a countertop mounted cooktop. The hardest part of the repair was getting the cooktop out of the hole and separating the glass top from the burner box. It is highly recomended that you have two people to seperate the top from the burner box. Be sure you turn off the breaker to the cooktop first before you do any work. One time sav
... Read more
er is once you have the top sperated from the box use 2- 10"-12" pieces of 1x2 or 2x4 to prop the top open. This will eleminate the need to disconnect the power leads (be sure the breaker is OFF). If you are not electrically inclined mark the color of the wires to the corrosponding terminals on the new element BEFORE you remove them from the old element. The element that I replaced was the dual heat element. I ended up having to change 2 of the terminal ends on the wiring harness becacuse they were too small for the new element. Carefully remove the wires from the old elenent using needle nose pliers and remove the old element by removing the 2 screws that hold the element to the hold down clips, then loosen the clip mounting screws & remove the element. Change terminals if needed & reassmble in reverse order. Once I got it reassembled with a couple of the top mounting screws in, I turned on the breaker and tested for proper operation. Breaker OFF, finish reassembly and remount. You may want to consider replacing foam gasket before remounting. Good luck... R. Moore
Read less
Parts Used:
-
Richard from Weatherford, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 controls were damaged and not working correctly. One would not properly shut off.
1. Turned off the 240V branch circuit to the cooktop.
2. Removed and inverted the cooktop.
3. Removed the bottom panel, used 1/4-inch nut driver to remove the sheet metal screws.
4. Confirmed the circuit was de-energized. Voltmeter set to AC, measure across the L1, L2 connections, should be 0 VAC or very close.
5. Make ... Read more a diagram of the existing connections to the controls to be replaced, note all control markings (L1, L2, H1, H2, PL) as the replacement controls have connectors in different locations.
6. Remove the AC Mains plate, 2 sheet metal screws.
7. Make a diagram of the primary AC distribution blocks.
8. Remove the AC Mains input leads, Red and Black.
9. Remove the AC distribution to the controls from the primary AC distribution blocks. Needed to free up the control panel.
10. Remove the 4 sheet metal screws holding the control panel.
11. Rotate the control panel to access the screws holding the controls. Caution on the wires to the heating elements, watch for pinching.
12. Remove one control with the wires attached.
13. Install the replacement control. Secure the screws.
14. Transfer the wires, matching the connection marking (L1, L2, H1, H2, PL) exactly.
15. Do the same (12, 13, 14) with the next control.
16. Re-install the control panel. Check all wires for clearance.
17. Re-connect the control wiring to the AC primary distribution blocks.
18. Re-connect the AC mains wiring to the primary AC distribution blocks.
19. Re-install the AC mains plate.
20. Visually check all the connections. Shake out any debris.
21. Replace the bottom cover, installing all screws.
22. Remove the gasket strip from the mounting lip, clean the surface, install new gasket (weather stripping).
23. Re-mount the cook top.
24. Energize the 240VAC branch circuit.
25. Test the controls. Correct any errors.
26. Done! Go have some hot tea! (or a beer)
2. Removed and inverted the cooktop.
3. Removed the bottom panel, used 1/4-inch nut driver to remove the sheet metal screws.
4. Confirmed the circuit was de-energized. Voltmeter set to AC, measure across the L1, L2 connections, should be 0 VAC or very close.
5. Make ... Read more a diagram of the existing connections to the controls to be replaced, note all control markings (L1, L2, H1, H2, PL) as the replacement controls have connectors in different locations.
6. Remove the AC Mains plate, 2 sheet metal screws.
7. Make a diagram of the primary AC distribution blocks.
8. Remove the AC Mains input leads, Red and Black.
9. Remove the AC distribution to the controls from the primary AC distribution blocks. Needed to free up the control panel.
10. Remove the 4 sheet metal screws holding the control panel.
11. Rotate the control panel to access the screws holding the controls. Caution on the wires to the heating elements, watch for pinching.
12. Remove one control with the wires attached.
13. Install the replacement control. Secure the screws.
14. Transfer the wires, matching the connection marking (L1, L2, H1, H2, PL) exactly.
15. Do the same (12, 13, 14) with the next control.
16. Re-install the control panel. Check all wires for clearance.
17. Re-connect the control wiring to the AC primary distribution blocks.
18. Re-connect the AC mains wiring to the primary AC distribution blocks.
19. Re-install the AC mains plate.
20. Visually check all the connections. Shake out any debris.
21. Replace the bottom cover, installing all screws.
22. Remove the gasket strip from the mounting lip, clean the surface, install new gasket (weather stripping).
23. Re-mount the cook top.
24. Energize the 240VAC branch circuit.
25. Test the controls. Correct any errors.
26. Done! Go have some hot tea! (or a beer)
Read less
Parts Used:
-
Edward from Sunnyvale, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!