All Installation Instructions for Amana Range AGC585LL

There was a crack in the porcelain not letting it spark

I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.

Parts Used:

Spark Electrode

Billy from Martinsville, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

23 of 36 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken ignitor insulation; repeated sparking after burner lit

Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!

Parts Used:

Spark Electrode

Joe from San Bruno, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)

15 of 21 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Purchased home but stove had no broiler pan.

Purchased 2 piece broiler pan from this site

Parts Used:

2 Piece Broiler Pan

Raymond from BLOOMINGTON, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

16 of 31 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No leveling legs

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

Parts Used:

Refrigerator Leveler

stephen from montgomery, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Spark Ignition Electrode was not sparking properly

Used a pair of pliers and pulled firmly on ignit. elect. till the retaining clip pulled off the bottom of the elect.The wire pulled off the bottom of it and I had to use a long- thin- nose set of needlenose pliers to pull the wire out of where the elect. came out.Plugged wire in place and snapped electrode back in place without using the retainer clip.Works great.Thanks Wade

Parts Used:

Spark Electrode

Wade from Jacksons Gap, AL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

5 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

top oven gasket replaced

shortened gasket for this oven. moved hook approx. 1 inch. used high temp adhesive. simple fix.

Parts Used:

Oven Seal - Top or Bottom

dennis from WESTFORD, MA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

igniter on top right front burner was shorting out,it would click but not ignite burner

removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.

Parts Used:

Spark Electrode

Shelly J from KAPLAN, LA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

stove gas burner would not light?

TURN OFF THE GAS SUPPLY & POWER TO THE STOVE. Disconnect the gas line & power source to the stove. Remove the complete counter top stove and place it upside down on a flat surface to enable you to remove all the surrounding small screws with a nut driver, then separate the bottom from the top accessing the retaining ring holding the ceramic electronic Ignition in place, remove the electric wire from the the old igniter. The most difficult part of the job was removing the retaining ring and installing the new ring.Job successfully completed.

Parts Used:

Spark Electrode

Robert from Hendersonville, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Renters removed leveling legs from refrigerator. I don't know why!

I tilted the unit back enough to scew the new legs into the threaded holes.

Parts Used:

Refrigerator Leveler

Don from Frankfort, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broiler pan missing

ordered new broiler pan

Parts Used:

2 Piece Broiler Pan

RAYMOND from JACKSONVILLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven door would not stay closed [Broken hinge]

Slid the oven door off the hinges. Removed the 4 srews in the old hinges. Pulled the old hinges out of the front of the oven cabnet. installed new door hinges in oven cabnet with the 4 mounting srews.slid oven door on new hinges.

Parts Used:

Door Hinge

Ronald from Avon Lake, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replace top oven seal

This is a simple replacement. The hardest part was that I had to shorten the seal because it comes 15 to 17 inches. So it needed to be shortened to properly fit. I cut the seal to fit, then took the metal hook on the end and super glued it to the cut end. I put a weight on it to make sure

Parts Used:

Oven Seal - Top or Bottom

Linda from Oxnard, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

no ignition on right frt burner

removed one screw lifted he brner took retainer off unpluged the igniter it had broken porcelen reversed the procedure everything worked fine

Parts Used:

Spark Electrode

CHARLES from CHICAGO, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Dual element outer ring not working.

Took off the back panel, unplugged the power cord, and tested the switch with an ohm meter. Found it open and ordered new switch. Replaced it easily and now have both elements working as required.

Parts Used:

SWITCH- RO

James from Bowdoinham, ME
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

Broiler door would not go all the way in.

Removed broiler door springs, removed door slide arms that attach to broiler tray, two screws on each side. Removed tray and replaced slide guides. Instassed in reverse order. Works great: Thanks, Best thing about this repair was that the parts ordered were right and fit..........

Parts Used: