Parts That Fix Speed Queen Dryer ADE30RGS171TW01 Not Heating
Not Heating is a commonly reported symptom for the ADE30RGS171TW01 Speed Queen Dryer, and we have put together a full guide
... Read more
on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your ADE30RGS171TW01 Speed Queen Dryer that will fix Not Heating.
We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Read less
Not Heating is a commonly reported symptom for the ADE30RGS171TW01 Speed Queen Dryer, and we have put together a full guide on how to fix this.
This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your ADE30RGS171TW01 Speed Queen Dryer that will fix Not Heating.
We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Fixes Symptom 96% of time
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. The coils are attached to the dryer gas valve. If the dryer does not heat or heats intermittently, the coil may not be opening the gas valve. Both coils must be operational for the valve to open. No continuity would indicate a defective coil, but they can be intermittent and fail when they get hot. Both coils should be replaced when one of them is broken. This part can break as a result of material fatigue from normal use. This part measures approximately 1 inch in diameter and 1 inch in height, and is constructed of plastic and metal. It comes in black/beige. This part features a 3-terminal boost/hold coil and a 2-terminal secondary coil
$
28.42
In Stock
PartSelect Number PS334310
Manufacturer Part Number 279834
Customer Repair Stories
Dryer would only heat cycle once
I removed the two screws holding the front panel to expose the lower works and verified the heating cycle failure. After a check of the vent system, checking the sensors for continuity and coils for resistance, I retired to the 'net for support. Accepting the general consensus that the most frequent, common and likely failure to be the c
... Read more
oils, I rechecked them with the meter and found the two pronged coil to have significantly more resistance than the three prong coil. That was enough evidence to point to the coils. While I waited for the part to arrive, I replace the vent ducting. When the parts arrived I removed the two Phillips screws holding the coils, removed the old ones, installed the new ones, replaced the bracket, put the front cover back on and in less then ten minutes clothes where drying.
Read less
-
Robert from Seattle, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
88 of 99 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer ran but would not heat
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are
... Read more
located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.
Read less
-
Gary from Haverhill, NH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
419 of 479 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 Igniter
Fixes Symptom 4% of time
The bracket is no longer included.
$
47.40
In Stock
PartSelect Number PS11741932
Manufacturer Part Number WP37001308
Customer Repair Stories
Would not lite
Remove igniter and replaced easy to do
-
RICHARD from LINDSTROM, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas dryer was not getting hot.
Removed top of dryer and front panel. Keeping the front door closed I was able to start the unit and observe if the gas was igniting to heat the unit.
Found that no flame was present.
Examined the ignitor (found the locatino after utilizine this website parts diagram) and noticed it was cracked.
Ordered the new part and it ... Read more arrived two days later. Simple installation and ta daaa....ignitor works, hot dryer again.
*Only reason it took over half an hour was because I cleaned out all the internal vents while the unit was opened.
Basic mechanical abilities required here but remember to unplug the unit while working on it!
Found that no flame was present.
Examined the ignitor (found the locatino after utilizine this website parts diagram) and noticed it was cracked.
Ordered the new part and it ... Read more arrived two days later. Simple installation and ta daaa....ignitor works, hot dryer again.
*Only reason it took over half an hour was because I cleaned out all the internal vents while the unit was opened.
Basic mechanical abilities required here but remember to unplug the unit while working on it!
Read less
-
William from Placentia, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
11 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!