Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ACF3355AC (PACF3355AC0)

ACF3355AC (PACF3355AC0) Amana Range - Overview

Get Parts and Repair Help for ACF3355AC

If you know the range repair part you need, you can browse the list of all parts on the ACF3355AC, or you can search by name or part description. You can also find your part by where it is located on the ACF3355AC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$67.57

Igniter - Horizontal Mount

This can be used for either the bake igniter or broil igniter in your appliance. NOTE: The part may differ in appearance but will function the same as the original.

$17.94

Spark Ignition Electrode

This spark ignition electrode lights the gas that starts the burner on your range or cooktop. This electrode is part of the burner assembly, sits next to the burner head, and is just over an inch in length. It pulls current from the ignition circuit; the more current it pulls, the warmer it gets. When the spark ignition electrode reaches a certain temperature, it creates a spark. This electrode comes with the mounting bracket you will need to successfully install the part. Before installing your new part, shut off the gas supply and unplug your appliance. This part cannot be repaired. If it is damaged or faulty, it must be replaced.

$5.54

Bumper Pad Set of 4

***NOTE: This part has been substituted by the manufacturer and may not appear the same as the original but should function the same. These pads go on the bottom of your gas cook...

$3.12

Screw

Sold Individually.

$2.96

Frame Screw

Sold Individually.

$4.63

Drawer Wheel

Also known as a roller.

$4.88

Screw

$94.31

Spark Module

This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

$104.77

Surface Burner Head

Sold individually.

$69.28

SENSOR

This temperature sensor detects the temperature within the oven cavity.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The broiler would work but the stove would not lite. I saw the igniter getting to a glow on the broiler and lite but the stove it would not so I figured the igniter might be shot.

  • Customer: Robert from plymouth, NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 46 of 50 people found this instruction helpful
1st I opened door to stove and removed the wire racks. Then removed lower panel to get to igniter. Then I had to slide stove away from wall. Remove panel on back for accesss to wires. The new part had a plastic connector and the original just used wire nuts for the connection. So I cut off connector and stripped 1/2 inch of the end. Removed wire nuts from ol... read more

Broken Electrode, no spark

  • Customer: HUY from ALISO VIEJO, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 46 of 56 people found this instruction helpful
Remove 2 screws holding the top burner. Remove 1 screw holding the electrode. Remove electrode from wiring using plier. Install new electrode and top burner read more

Burner would not ignite when control in "light" position

  • Customer: Michael from Friendswood, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 19 of 21 people found this instruction helpful
Remove the two screws from the burner assembly (on top of the burner). Lift burner assembly from the cook top. Disconnect the electrode wire from the electrode. Remove the screw holding the electrode to the burner assembly (on bottom of burner). Install the new electrode and attach the electrode to the burner assembly. Attach the electrode wire to the el... read more