Models > A107

A107 Maytag Washer - Overview

Sections of the A107

[Viewing 18 of 18]
Keep searches simple, eg. "belt" or "pump".
Belt Kit – Part Number: 12112425
Belt Kit
★★★★★
★★★★★
(64)
PartSelect #: PS2005284
Manufacturer #: 12112425
This kit includes both the drive belt and the pump belt which are both V-shaped. If your washer does not toss, spin, or drain water properly, this might be because one of these belts has worn or stret...
$43.12
  In Stock
Water Inlet Valve – Part Number: 205613
Water Inlet Valve
★★★★★
★★★★★
(32)
PartSelect #: PS1583805
Manufacturer #: 205613
This is a water inlet valve which is used in washing machines. The valve controls and monitors the flow of water into the washer. It has a multi-mount bracket and outlet adaptor. The tools needed for ...
$95.82
  In Stock
Rubber Injector Valve – Part Number: WP216201
Rubber Injector Valve
★★★★★
★★★★★
(33)
PartSelect #: PS11738945
Manufacturer #: WP216201
This part is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle. It is black in color and measures approximately 2 inches in length. To access thi...
$16.35
  In Stock
Mounting Stem/Tub Seal Kit – Part Number: 6-2095720
Mounting Stem/Tub Seal Kit
★★★★★
★★★★★
(14)
PartSelect #: PS2351899
Manufacturer #: 6-2095720
This kit comes with a hub assembly, agitator seal, and spanner nut. If your washer leaks once it is full (with or without clothes in it) or leaks during agitation, then you should replace the seal. Th...
$123.42
  In Stock
Plastic Injector Nozzle – Part Number: WP213015
Plastic Injector Nozzle
★★★★★
★★★★★
(7)
PartSelect #: PS11738878
Manufacturer #: WP213015
The plastic injector nozzle is used in washers and dryers. It is 3 inches long and is white in color. If your washer is leaking water, replacing the nozzle could solve your problem. For this repair pr...
$8.79
  In Stock
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.76
  In Stock
Lid Switch – Part Number: W10820036
Lid Switch
★★★★★
★★★★★
(16)
PartSelect #: PS11723153
Manufacturer #: W10820036
This 3 prong lid switch is used for washing machines that do not have a tub light.
$27.88
  In Stock
Hose Clamp – Part Number: WP596669
Hose Clamp
★★★★★
★★★★★
(1)
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$7.76
  In Stock
Drain Pump – Part Number: WP6-2022030
Drain Pump
★★★★★
★★★★★
(17)
PartSelect #: PS11743017
Manufacturer #: WP6-2022030
This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.
$94.36
  In Stock
Rubber Foot Pad – Part Number: WP210684
Rubber Foot Pad
★★★★★
★★★★★
(1)
PartSelect #: PS11738859
Manufacturer #: WP210684
The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is ju...
$12.68
  In Stock

Questions And Answers for A107

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the A107

[Viewing 16 of 16]
Leaking
Fixed by
these parts
Show All
Burning smell
Fixed by
these parts
Show All
Will not drain
Fixed by
these parts
Show All
Noisy
Fixed by
these parts
Show All
Shakes and moves
Fixed by
these parts
Show All
Will not agitate
Fixed by
these parts
Show All
Pumps but will not spin
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Will not stop filling with water
Fixed by
these parts
Show All
No hot or cold water
Fixed by
these parts
Show All
Will not fill with water
Fixed by
these parts
Show All
Spins slowly
Fixed by
these parts
Show All
Timer will not advance
Fixed by
these parts
Show All
Will not shut off
Fixed by
these parts
Show All
Lid or door won’t close
Fixed by
these parts
Show All
Lid or door will not open
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cold water valve only opened to a trickle
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place. I then pulled the assembly out about 3 inches and disconnected the two wire plugs. The last step was to loosen the hose clamp on the outlet hose and pull off the outlet hose. I reversed the steps to install the new assembly and the total repair took about 10 minutes.
Parts Used:
Water Inlet Valve
  • Brian from El Cajon, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Wrench (Adjustable)
575 of 585 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum would not drain and there was a banging noise when the drum spun
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
Parts Used:
Belt Kit Belt Kit
  • Charles from Whitman, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
534 of 572 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leaking from around center shaft below fixed tub
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came across your site. By looking at your diagrams, I determined what parts I needed and ordered them. The parts arrived in 2 days, and I installed them. There were no leaks and it cost me under $70 (a repairman would have cost at least $250). The only thing I would recommend to those in similar situations, is to purchase a spanner wrench (your site does not sell, but others do). The stem seal and hub assembly is reverse threaded (clockwise to loosen) and is difficult to remove due to tight quarters in the tub.
Parts Used:
Mounting Stem/Tub Seal Kit
  • douglas from bonita springs, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Socket set
506 of 518 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!