9797-1 Briggs and Stratton Generator - Overview
Sections of the 9797-1
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Fuel Valve With Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$27.33
In Stock
Assembly, Holder, Brush
PartSelect #: PS9063496
Manufacturer #: 66386GS
The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached spri...
$32.55
In Stock
Pre-cleaner,airfltr
PartSelect #: PS11923829
Manufacturer #: G081646
This is an original Generac replacement part manufactured for use with portable generators. The foam pre-filter traps dirt along with the main air filter to prevent contamination inside the engine. Th...
$11.14
In Stock
Cap-fuel Tank
PartSelect #: PS11830156
Manufacturer #: 846987
This is a genuine OEM sourced component that is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is designed to keep the fuel in the tank...
$33.99
In Stock
Hose Breather Gh410 Engines
PartSelect #: PS9873851
Manufacturer #: 0D7199A
This authentic manufacturer-sourced component is constructed of flexible plastic, and is made for use with several portable generators. The breather hose (gh410 engines) is secured onto the crankcase,...
$34.24
On Order
Common Symptoms of the 9797-1
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
-
John from LEES SUMMIT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
9 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!