Models > 9114742593

9114742593 Kenmore Wall Oven - Overview

Sections of the 9114742593

[Viewing 5 of 5]

Manuals & Care Guides for 9114742593

Click to download
Keep searches simple, eg. "belt" or "pump".
Bake Element – Part Number: WB44K5013
Bake Element
★★★★★
★★★★★
(30)
PartSelect #: PS249249
Manufacturer #: WB44K5013
This bake element is used in ranges and located at the bottom of the oven. The bake element supplies heat for baking. If your symptoms include: your oven is not heating evenly, not starting, or the he...
$78.70
  In Stock
Single Heating Element Support Clip – Part Number: WB2X9719
Single Heating Element Support Clip
★★★★★
★★★★★
(7)
PartSelect #: PS243701
Manufacturer #: WB2X9719
The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this r...
$15.08
  In Stock
Light Bulb - 40W – Part Number: 40A15
Light Bulb - 40W
★★★★★
★★★★★
(6)
PartSelect #: PS217532
Manufacturer #: 40A15
$9.42
  In Stock
Broil Element - 240V – Part Number: WB44K5009
Broil Element - 240V
★★★★★
★★★★★
(19)
PartSelect #: PS249244
Manufacturer #: WB44K5009
This oven broil element has push-on terminals.
$61.24
  In Stock
Oven Sensor – Part Number: WB21X5301
Oven Sensor
★★★★★
★★★★★
(5)
PartSelect #: PS236043
Manufacturer #: WB21X5301
It is possible that your oven is cold because of a fault in the temperature sensor. The temperature sensor regulates oven temperature in modern ranges, like a thermostat. It is on the back wall near t...
$160.05
  In Stock
SCREW – Part Number: WB1K5062
SCREW
PartSelect #: PS234148
Manufacturer #: WB1K5062
$8.63
  In Stock
Screw – Part Number: WH2X930
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$8.63
  In Stock
Broiler Pan - Large – Part Number: WB48X10056
Broiler Pan - Large
★★★★★
★★★★★
(10)
PartSelect #: PS1517612
Manufacturer #: WB48X10056
This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures ...
$28.82
  In Stock
Light Cover – Part Number: WB36X192
Light Cover
★★★★★
★★★★★
(8)
PartSelect #: PS247415
Manufacturer #: WB36X192
This light bulb lens covers the interior light bulb in an oven, range, or stove. No tools are necessary to replace this part. Simply slide off the wire bracket to remove the existing light bulb lens. ...
$9.42
  In Stock
Screw – Part Number: WB1M1
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS234320
Manufacturer #: WB1M1
Sold Individually.
$6.46
  In Stock
Screw – Part Number: WB1X1130
Screw
★★★★★
★★★★★
(2)
PartSelect #: PS234427
Manufacturer #: WB1X1130
Sold Individually.
$6.68
  In Stock
Oven Rack – Part Number: WB48T10093
Oven Rack
★★★★★
★★★★★
(5)
PartSelect #: PS6447645
Manufacturer #: WB48T10093
Sold individually.
$65.55
  In Stock

Questions And Answers for 9114742593

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

2 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Chester
    January 2, 2020
    I need the list of fault codes and what each one means
    For model number 9114742593
    Hi Chester, thank you for your question. You will either have to get that from your brand manufacturer or you can look at a resource on our website that may help you here: https://www.partselect.com/JustForFun/Fault-Codes.aspx. Good luck with your repair.

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Chester
    December 26, 2019
    Where can I find a fault code for the errors?
    For model number 9114742593
    Hello Chester, Thank you for the question. In order to trouble shoot the error code we will need to know what error code you are getting. Please submit a new question if you have any follow ups. We are looking forward to hearing from you!

    Was this helpful?
    Thank you for voting!

      Common Symptoms of the 9114742593

      [Viewing 6 of 6]
      Little to no heat when baking
      Fixed by
      these parts
      Show All
      Element will not heat
      Fixed by
      these parts
      Show All
      Little to no heat when broiling
      Fixed by
      these parts
      Show All
      Oven not heating evenly
      Fixed by
      these parts
      Show All
      Oven is too hot
      Fixed by
      these parts
      Show All
      Will Not Start
      Fixed by
      these parts
      Show All
      Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
      Oven tempature was approximately 150 degrees to low
      This repair is EASY if you know how to use an ohm meter. If not, seek help for this step.

      SYMPTOM:
      The oven (JKP27WOP3WG or JKP27WP3WG and many ovens like it ) was not getting hot enough. Verifying the cooking temperature with an typical oven thermometer, I was able to determine that the oven was cooking temperature was about 150 degrees to low.

      FAILURE POINTS:
      There are two logical failure points (1) The oven sensor ( WB21X5301 about $75), or the (2) the controller board (PS238233 about $252). In my case it was the controller board. When replaced the oven worked beautifully.

      REPAIR:
      As with any repair, you MUST DISCONNECT POWER TO THE UNIT BEFORE SERVICING!!!

      Pull oven from the wall:
      - Disconnect power by flipping the circuit breaker to the OFF position.
      - Remove the top flange / cowling from the top of the oven (it just pulls off)
      - Remove two screws under the top flange / cowling
      - The whole unit easily slides out, but it is highly recommended that you use two people to place the oven on the floor.

      As a diagnostic between these two parts, if the oven sensors measure approximately 1.1K ohms of resistance at room temperature, then it is probably not the sensor. The oven sensor wires are connected to two white wires that run up to the controller board. You need to disconnect the oven sensor to make the measurement. You may either completely remove the oven sensor by cutting the wire (be sure to allow yourself enough slack so that they may be safely reconnected) where it connects to the white wires, OR, (preferred method) if leaving the oven sensor partially installed,
      - Remove the top sheet metal cover (10 screws)
      - Remove the service connect cover (2 screws - this is where the main Power cord comes into the unit)
      - Disconnect the white wires from the controller board (this connector which also includes other circuits is on the left side when looking at the controller board).
      - Remove two screws from oven sensor but just let in dangle down so that you can put the sensor in the ice water / boiling water.

      Measure the resistance under the following conditions. Your ohm meter should read APPROXIMATELY...
      - 1.02K ohms in ice water
      - 1.09K ohms at room temperature
      - 1.36K ohms in boiling water.
      If you get approximately these readings, then it is NOT the oven sensor. If that checks out then re-install the sensor AND the connector.

      If it is NOT the sensor, replace the controller board.
      - Take a moment to write down the color of the wire to the LETTERING (N, L, G, C / COM,,,) on the controller board. The connectors are in different locations on the new controller board so the wire color to the letter designation is significant.
      - Carefully remove the wires one at a time
      - VERY carefully remove the keypad ribbon cable from the right side of the controller board.
      -- The ribbon cable will disconnect by releasing some little pressure clips on the side of the connector.
      - Remove the controller board (4 screws)
      - Install new controller board (4 screws)
      - VERY carefully connect the keypad ribbon cable on the right side.
      -- Make sure that the connector is in the OPEN position first, then,
      -- Slide in the cable ensuring that all parts of the ribbon made it into the connector, then
      -- Press down on the connector locking tabs.
      - Reconnect each wire to the correctly lettering on the board.
      -- Again, the connectors MAY BE in a different order on the replacement controller board. Match color to letter.
      - Reconnect the (5 wire?) connector that includes the white oven sensor wires.
      - Make sure everything looks normal, (i.e. no wires are pinched, remove tools from top of oven area, etc.)
      - Re-install top cover.
      - Re-install service connect cover.

      You can test the unit while it is out of the cabinet,
      - Make SURE that all sheet metal covers are in place.
      - Flip power breaker to "On".
      - Test that oven gets to the desired temp.
      Parts Used:
      Oven Sensor
      • James from Austin, TX
      • Difficulty Level:
        Easy
      • Total Repair Time:
        1- 2 hours
      • Tools:
        Nutdriver, Screw drivers
      218 of 254 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      bake element shorted out, sparking like a sparkler
      first, made sure circuit breaker was off
      second, used nut driver to remove 2 screws on old element, pulled it from the back of the oven
      third, removed 2 wires from old element (spade connectors)
      fourth, connected new element and pushed back into oven.
      fifth, reinstalled 2 screws securing new element

      this was all done by my 15 yr old son under my supervision.
      Parts Used:
      Bake Element
      • Carl from Wynnewood, PA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Nutdriver
      89 of 96 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      The broiler element caught fire and burned out while I was broiling a steak.
      First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches, but I had not turned off the power.
      So, I shorted out one of the wires. Then I turned off the power but was afraid to go any farther.
      An appliance repairman was at my house that day fixing my dryer seal. He was able to pull the wires through the insulation successfully and install the broiler element. He did not charge me any extra for this little extra job. But I learned my lesson. Cut the power before you begin! He told me that I could have wound up with a much bigger repair if the short had been in the wire that is connected to the control panel of the oven. I was very lucky!
      Parts Used:
      Broil Element - 240V
      • Dianne from Rockville, MD
      • Difficulty Level:
        Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Nutdriver
      64 of 71 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!