Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 79691538110

79691538110 Kenmore Dryer - Overview

Get Parts and Repair Help for 79691538110

If you know the dryer repair part you need, you can browse the list of all parts on the 79691538110, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$32.77

Drum Support Roller

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rol...

$30.05

Lint Filter

The lint filter is designed for use in your dryer. The function of the lint filter is to catch lint and debris during the operation of the dryer. If your old lint filter is old or damaged, or there are marks left on your clothes at the end of the dry cycle, you will need to replace it with this part. This part is approximately 12 inches in width by 11 inches in height. Many of our customers have rated this repair as very easy. To complete the repair, simply remove the old filter, clean up any remaining lint and debris, and install the new filter. NOTE: As per manufacture - due to a redesign you MAY also have to change the cover and filter guide.

$5.72

Sensor

The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough...

$15.54

THERMOSTAT

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside your dryer drum. As the air is being measured, it will turn the heat on or off in order to maintain a stable temperature within the drum. The most common reason you would need to replace your thermostat is if your dryer is not receiving enough heat, or any heat at all.The tools you will need to complete this repair include a Phillips screwdriver, and a flat-head screwdriver.

$17.98

Thermistor,NTC

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce e...

$26.70

BELT,POLY V

This dryer belt helps rotate from the drive motor to the drum. It is located between the motor and the tub. If you notice that your dryer is noisy or is not tumbling this could be due to your belt needing to be replaced. This belt is long, black, and slim (1/4-inch wide). The belt wraps the length of the dryer drum, secured by a tension pulley and then loops around the motor pulley. If you find that the drum is not turning properly or at all while your dryer is in succession, it might be due to the belt being broken.

$32.77

Cover,Guide

$11.85

Guide,Filter

$14.73

ROLLER ONLY

$59.13

Gas Igniter

Comes with bracket and wire harness.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Gas Dryer not getting hot

  • Customer: Terry from Goose Creek, SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 14 of 18 people found this instruction helpful
I noticed the flame would start, then quit after about 15 seconds. I checked the flame detector, and found the lenze cracked. I replaced it, and it's as good as gold.

It looked like a hard job to take the drum out to get at the part. But the top was off with 3 screws, the front about 6 I think. Then the front frame, only 4 screws. I think sett... read more

Filter parts chipped - replaced

  • Customer: David from Annapolis, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 17 of 39 people found this instruction helpful
Removed existing parts using screwdriver, positioned new parts in dryer and re-inserted screws, tightened - done. Piece of cake, even for someone who cannot saw a straight line with a chop saw. read more

Lint filter and cover guide melted which was ripping up some clothes

  • Customer: Kevin from FARMINGVILLE, NY
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 9 people found this instruction helpful
Just unscrewed four screws. One piece stays behind which is a sensor then pull up on it, put it back in the same way, put the four screws back in and it was done. read more