This plastic holder is also known as a tine clip, or a rack flip tine clip. It is used in the lower rack of a dishwasher, it is part of the rack assembly that allows to convert your rack to better the...
$7.59
In Stock
Order within the next 12 hrs and your part ships today!
This dishrack wheel is designed for use on the lower rack of your dishwasher, it allows the rack to roll in and out of your appliance with ease. This roller wheel includes the locking clip required fo...
$18.55
In Stock
Order within the next 12 hrs and your part ships today!
This seal is also referred to as a door gasket, and it is designed for use on dishwashers. It is installed on the door of the appliance, and it seals the space between the tub of the dishwasher and th...
$31.10
In Stock
Order within the next 12 hrs and your part ships today!
This tine clip kit is designed for use in the lower rack of dishwashers. Some dishwashers have adjustable tines that allow you to convert the rack in your dishwasher to accommodate more dishes, and di...
$39.34
In Stock
Order within the next 12 hrs and your part ships today!
This micro filter basket assembly is used in dishwashers. The filter is responsible for filtering the water inside the dishwasher. All of the food and debris particles that are removed from your dishe...
$28.88
In Stock
Order within the next 12 hrs and your part ships today!
This door seal, also known as a door gasket, is an authentic manufacturer replacement part for your dishwasher. It is responsible for creating a watertight seal between the tub and dishwasher door and...
$43.16
In Stock
Order within the next 12 hrs and your part ships today!
A holder is used in dishwashers, it is known as the dishrack stop kit. This kit comes with both the front and the rear stop, these parts are installed at either end of the rails that the upper rack sl...
$12.03
In Stock
Order within the next 12 hrs and your part ships today!
This drain hose is designed for use in dishwashers. After the wash cycle is complete the water need to leave the dishwasher, this drain hose it carries the dirty water from the drain pump to the kitch...
$39.92
In Stock
Order within the next 12 hrs and your part ships today!
Here are the steps you need to take to do the job properly:
1. turn off electrical circuit breaker to the dishwasher 2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed. 3
... Read more. unplug the wiring harness to the detergent/rinse aid dispenser 4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser. 5. the unit will pop out toward the inside of the dishwasher 6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in. 7. re-attach the wiring harness 8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job. 9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks. 10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.
With the help of You Tube, this 50 year old Mom got the job done. Not that complicated if you watch the step by step instructions on the Appliance Pro video. My repairman and husband were both determined to just buy a new one but this 20 year old dishwashing genius was just in need of a little repair. Only need a screwdriver, and sli
... Read moreghtly confusing as wires hook on a little different on new pumps. I suggest watching video the whole way through and then playing it step by step as you do the repair. Worked great for me. Thanks.
The old Tine holders used on the upper and lower dish rack dried up and cracked/broke. So I purchased new Tine holders for the upper and lower racks and snapped the new parts in place.
