Models
>
63013913010
63013913010 Kenmore Dishwasher - Overview
Sections of the 63013913010
[Viewing 6 of 6]Manuals & Care Guides for 63013913010
Click to downloadKeep searches simple, eg. "belt" or "pump".
Rack Roller Wheel
PartSelect #: PS8727423
Manufacturer #: 00611666
This wheel is a dishwasher rack wheel designed for the upper rack of your appliance. The roller wheel is approximately 1.25 inches in diameters and includes the brushing you need for installation. It ...
$10.00
In Stock
Water Inlet Valve
PartSelect #: PS8726680
Manufacturer #: 00607335
This is a replacement water inlet valve for your washer. The water inlet valve in your washer connects to the water source and solenoid wires, and ensures the tub has the right amount of water enterin...
$62.65
In Stock
Drain Pump - 55Hz
PartSelect #: PS8727352
Manufacturer #: 00611332
The pump ejects the water from the dishwasher through the drain hose.
$59.42
In Stock
Dishrack Stopper Kit
PartSelect #: PS8697039
Manufacturer #: 00165254
A holder is used in dishwashers, it is known as the dishrack stop kit. This kit comes with both the front and the rear stop, these parts are installed at either end of the rails that the upper rack sl...
$12.03
In Stock
WHEEL
PartSelect #: PS10058839
Manufacturer #: 12004485
This wheel kit is used for the lower rack of your dishwasher. The kit includes 8 wheels and axels. To install you can simply clip the wheel onto the frame. There are eight wheels on the lower rack in...
$44.42
In Stock
Questions And Answers for 63013913010
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 63013913010
[Viewing 8 of 8]Not draining
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The plastic clip on the roller broke
We let this go for a shameful amount of time before I decided I could probably fix it. The roller broke so you could only pull it out about halfway or it would come off the track. I looked up the part, and bought it. Actually bought two in case it happened again. When I arrived I looked at how it was put together on the other side and t
... Read more
hen just basically pushed it onto the rod and it was fixed. I am ashamed it took so long to do it. Never be afraid to try it yourself. It was a total of $10 shipped to fix it.
Read less
Parts Used:
-
Catherine from AMHERST, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
20 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher was pouring water during the rinse cycle. put the machine up on milk crates to find the source of the leak. The water was coming from the bottom corner of the door. Fount the orig gasket torn
Remove the dishwasher from under the counter. Remove door springs. On the inside of the lip of the door remove the 6 screws that hold the outer door panel on, and remove panel. this will expose hinge screws. Remove the two screws per side holding the inner door to the hinge assembly. Take pictures of the way the gasket's grey plastic end
... Read more
cap assembles between the inner door frame and the hinge, and remove the inner door. The old gasket has a channel lip that sits on the plastic edge of the washer tub, pull it off this lip and discard. Install new gasket and put it all back together! Use this opportunity to clean the gunk out of the upper door seals.
Read less
Parts Used:
-
Harper from Charleston WV, WV
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not fill with water. Pump sound like it was running when starting cycle
It was necessary to pull the dish washer to access the valve located on the lower left front of machine. Some difficulty in disconnecting water inlet and outlet hoses to valve since spring clips used to secure hoses. Tight spaces to remove the old valve and install new valve. Used screw type hose clamp on reinstall in lieu of spring cl
... Read more
ips. May have been easier had I had the special pliers used to remove and install spring type clips.
Saved a minimum of $100 for service call.
Saved a minimum of $100 for service call.
Read less
Parts Used:
-
Max from JENKS, OK
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Socket set
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!