Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
60102-0015-XX Briggs and Stratton Engine - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
Discover the power of optimal engine performance with the Briggs and Stratton Starter Clutch. A vital piece of your garden equipments engine, this starter clutch engages your machines flywheel while k...
This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should ...
This is an authentic manufacturer sourced replacement part designed for use with a variety of lawn and garden equipment. This carburetor intake gasket which provides an air tight seal for the carburet...
The Breather Gasket is OEM and used to provide an airtight seal for the breather assembly. It is a gray part, attached between the breather cap and engine. Installation is rated "Easy" and will requir...
This is an OEM approved replacement part designed for gas trimmers/brush cutters. Its purpose is to filter out dust and debris from the air that goes into the unit. Over time it will get dirty and clo...
This is a genuine OEM sourced part which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is a standard hardware which may have multip...
This air cleaner element is supplied from original manufacturer. It is specially designed for use with Briggs and Stratton engines used on lawn and garden equipment. It is used to filter out dust from...
This replacement armature-magneto is specially designed for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It is an authentic part sourced directly from ori...
This is an authentic OEM component from Briggs & Stratton. The magneto armature screw is compatible with many lawn and garden engines. The hardened metal screw helps to mount the magneto armature. A w...
The clutch ball allows the center part of the ratchet to turn backwards freely but catch when turned forward in your engine. This is an OEM part that is made of metal, and it is silver in color.
Thi...
This is a Briggs & Stratton and Toro replacement part directly sourced from the manufacturer for use in engines, generators, tillers, blower-vacuums, and lawn mowers. The breather assembly is made of ...
No Longer Available
Questions And Answers for 60102-0015-XX
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Once I determined what OEM muffler I needed, installation was relatively easy. I have a 1982 4hp Briggs on my Snapper tiller. There was a 90* galvanized elbow coming out of the exhaust port, with a bezel nut to lock it down. Do not remove the elbow, even though it appears that you should. If you install the muffler without the elbow the m
... Read moreuffler will parallel the the vacuum for the carburetor and can melt the rubber couplers. Use the elbow to direct the heat away from the carburetor. Use a pipe wrench to lock down the bezel nut because the weight of the muffler, especially under vibration, can work loose and fall down on the tine belt cover and melt it. The bezel nut that comes with the muffler should also be used to lock down the muffler to the threaded intake bracket that comes with the muffler, not to replace the bezel nut for the elbow.
