5KSM195PSZHI0 KitchenAid Mixer - Instructions

My girlfriends' stand mixer failed when the accessory drive cap fell into the mixing bowl and jambed the beater, spliting the worm gear. The teeth on this gear are made of nylon and are molded to an aluminum center. This part is designed to fail in situations like this, saving the more expensive transmission parts. Following a repair manual I found online, I first removed the rear cover and pulled out the cord strain relief out from the base. Next I removed the drip cup from around the base of the planetary drive. I then used a pin punch to drive out the pin holding the planetary to the center shaft and removed the planetary. The unit was then inverted and I removed 4 screws holding the bottom cover to the gear case, and the 5 screws from around the planetary drive. The bottom cover was then lifted off. Three screws holding the worm gear bracket in place were then removed and the worm gear assembly lifted out. A small pin holds the worm gear to the shaft. I drove this out with a small pin punch and the shaft and worm gear were then removed. There is also a thrust washer on this shaft, and it's location is important. Make a note for re-assembly. The new gear was installed and the entire process reversed for re-assembly. A successful repair completed! My girlfriend would have replaced this $200 appliance, but I was able to repair it for less than $30 including shipping.

bought new wire whip for mixer, simple attachment.

I removed the rear cap, decorative strap, and decorative ring. Next I drove out the pin holding the mixing head. I then removed the 9 screws holding on the motor/gearing portion. This facilitated removal of the gearing from the motor assembly. I next laid in the new gears and calculated what thickness of fiber washers were needed to hold the gears in place. Reassembly was in reverse order of dissassembly.

This was my husband's first time to taking apart any mixer - much less a heavy duty KitchenAid. Since we could not find a local repairman, the only thing to do was try to repair it himself. Using your exploded view of the machine he found on the internet, he ordered a gasket which he felt would be needed to repair the mixer. When he tore the machine down, the problem was what he had suspected - original grease had liquified and the rest had turned black in color. He went to a local auto parts store and bought a can of wheel bearing grease. He cleaned out the old oil and repacked with about a half pound of the new grease. The most difficult part of the repair was inserting the roll pin to attach the ring gear housing to the output shaft. It was impossible for him to reinsert the original pin, so he bought a new tension pin with which he was able to work. The only part he has been unable to align is the lever to lock/unlock the machine. He managed to set it enough that it locks when the lever is pushed halfway. The machine works great but I would not advise a person without any mechanical ability to try to repair these mixers.

1st I check if there is a burnt smell, there was burnt smell from the board phase. Check the motor brush. Surely enough they're at max (not touching the motor anymore). Replaced both parts, put everything back together. Tested it, it works like a charm. It's been working for the last 2 weeks now!

I removed the lower unit along with the top unit, removed the gear, replaced the gear, then put back together. I removed the grease, saved most of it, then discarded what looked like the dirty grease. I cleaned inside thoroughly in case broken parts were inside. The three schematics were very helpful in re-installed. Mixer was 40 years old but works like new!

My kitchenaid mixer is at least 37 years old. Everything has worked fine after all these years except the screw cap was flimsy, still stainless steel, but not sturdy. So I tried to replace it , but was told it was too old and couldn't get the part. I contacted Part Select and found a screw cap from newer models fit perfectly and should outlast me and the mixer, it is a lot sturdier than original one. It also arrived in 2 days, which was fantastic. Thanks guys

We:
tipped the mixer over on its side
pulled the old feet off
put the new feet in place and pounded them w/our fists
set it back up on its new feet
smiled

you guys are great I ordered one day and the next day the wire whip was delivered!!!! Great job,thank you. Joanne

I actually didn't do the repair. I asked a friend who was a carpenter about what he thought was wrong with my mixer since it only had high speed which made mixing flour a snow storm. He said when his tools do that, it's the brushes. He ordered new ones and presto - my mixer works marvelously. He saved me from dumping a good mixer and $$$$$$$.

unscrewed the screw holding the old brush. carefully removed the spring and old broken brush. we did have some of the old brush left inside, so my husband used a very thin drill bit to break it up. then carefully inverted the stand mixer to allow the broken pieces to fall out. then we were able to install the new brush. works great. yeah!!

Took the old feet (5) off and put new on the Kitchen Aide, looks great. Stands high and your assistance on the phone, was so appreciated.

first removed the dress ring by tapping it very gently.then drive the pin out that holds the beater plate on, now wiggle it off, then you can see the screws that hold the gear reducer on. remove them. take that off and you will see the housing that hold the worm gear. remove the 3 screws that hold it down . Now you will have to drive the drift pin out that holds the worm gear in place, slide the shaft out then remove gear. reverse order to assemble

My early '60's Kitchenaid K45 mixer screw cap/base plate would no longer hold the bowl, so I looked for another. This item, though not an exact replica of the original, fit and works great. The design is better by being more stout than the original. Pretty straightforward installation: remove three screws, take out old base plate, install new plate and screw down.

Very messy as there is lots of heavy grease inside the mixer and you have to fish out the blown gear parts. I vary glad I took shop class in High school as it preped me for the job. The machanical drawing you provide were very useful but you should mention the grease.

Mixer works just like new. and I got the parts in two days with standard shipping. Pizza on Thursday and fixed by Saturday