Models
>
58714669201B
58714669201B Kenmore Dishwasher - Overview
Sections of the 58714669201B
[Viewing 4 of 4]Manuals & Care Guides for 58714669201B
Click to downloadInstall
Installation Instructions
(1.48MB)
Specs
Product Specifications Sheet
(0.11MB)
Wiring
Wiring Diagram
(0.11MB)
Keep searches simple, eg. "belt" or "pump".
LATCH DOOR
PartSelect #: PS17219598
Manufacturer #: 5304535183
This is an OEM latch, which works with dishwashers.
$27.04
On Order
GASKET
PartSelect #: PS12365259
Manufacturer #: 5304512895
The door gasket provides a waterproof seal between the tub and the door.
$44.35
In Stock
Questions And Answers for 58714669201B
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 58714669201B
[Viewing 6 of 6]Leaking
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken latch
removed front face of dishwasher removed 2 screws holding latch and removed 2 push in plugs reinstalled the same.
job completed in less than 15 min.
job completed in less than 15 min.
Parts Used:
-
Daniel from Cutchogue, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
28 of 40 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking out onto floor when not in use!
Remove front Fascia on floor, use AC sniffer find hot wires into unit. Flip circuit breaker at panel. Verify no AC, shut water valve off on Dishwasher supply. Disconnect two valve wires to solenoid. Use wrench set to find proper size and use to remove supply line. Unscrew two Phillips sheet metal screws that hold valve support bracket and
... Read more
remove bracket with it now being held in by water inlet valve hose to interior wall of Dishwasher. Use Tin Snips to cut off metal band securing hose to old water inlet valve. Place new valve onto inlet hose, secure with new hose clamp (you must supply) tighten hex nut on clamp till water tight. Fasten wires onto the solenoid and mount assembly support bracket to dishwasher. Now connect water supply line after wrapping threads with pipe dope tape fasten and secure nut with adjustable wrench till water tight open supply valve and look for leaks with a flash light. If no leaks, reset breaker and test run and drain. No leaks replace fascia and have a Beer great Job saved $850 min. on a new dishwasher!
Read less
Parts Used:
-
Paul from Belmont, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door would not lock
-
William from Clarkfork, ID
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!