Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a replacement air filter/AC cartridge for your small engine. The air filter prevents dirt and debris from entering the engine. Over time, the air filter can become clogged or damaged, and this...
The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will...
This needle and seat kit, also known as a float valve, is found in many types of liquid-fueled lawn equipment, such as carburetors. The valve regulates the flow of fuel into the float bowl. The needle...
This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out ...
Upgrade your equipment with this reliable Pulley/Spring Assembly from Briggs and Stratton. Known for their superior quality, Briggs and Stratton parts are designed to help prolong the life of your mac...
This is a Genuine Manufacturer Sourced replacement part used on a a variety of Engines. This is a Fuel Line Connector connects the fuel line to the carburetor. This part is made out of Plastic and Met...
This is a Genuine OEM Authorized Gasket used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recom...
Genuine Manufacturer Sourced replacement part used on a variety of Briggs and Stratton Engines. This filter adds a second layer of protection against airborne-dirt particle ingestion. This is a Foam P...
This item is an authentic replacement part that has been sourced from the original manufacturer to be used with lawnmower engines from Briggs & Stratton and Toro. The metal float bowl fits onto the bo...
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
This replacement part is designed for use with Briggs and Stratton engines installed on lawn and garden equipment. It is used to filter out dust and debris from contaminating engine and carburetor. Th...
This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should ...
$7.47
In Stock
Order now and your part arrives by Mar 28
Questions And Answers for 5516RT
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed tank and drained old gas. Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner. Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again. Cleaned spark plug electrode. Reassemble
... Read mored, poured Sea Foam in the bottom of the tank and gave it a few pulls. Let Sea Foam sit for a while, then filled the tank with Premium. Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Using a socket wrench with extension and a T20 star socket (you can use the appropriate hex head socket also) i removed to two bolts holding the muffler on. They are right on top of the engine and very accessible. Your model may have a heat shield that needs to be removed. Once the muffler is off remove the old gasket. It may be stuck to
... Read morethe muffler or exhaust opening on the engine. It should just pry of with a little effort. I did make sure there were no gasket pieces left behind. I placed the bolts through the flange of the new muffler and then slid the new gasket over the bolts. You can use a exhaust gasket sealant just hold it place while you place the flange in place and not have to worry about gasket dropping off. I just held it until I got the flange in place. I started the bolts by hand using the socket and extension. I alternated from each bolt until I had tighted it down. You can look up torque specs. I just used my grunt meter. It is good as new. Parts were OEM replacement. Not knock off almost right parts. I got very lucky when I found this company and will use them again.
Removed old broken rewind starter (4 bolts); found the Model and Serial numbers; found Parts Direct and ordered new assembly; upon delivery, reinstalled with new Starter and hardware.
