Models > 49-2828-00-01

49-2828-00-01 Tappan Dryer - Overview

Sections of the 49-2828-00-01

[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Rear Drum Bearing Kit – Part Number: 5303281153
Rear Drum Bearing Kit
★★★★★
★★★★★
(98)
PartSelect #: PS459829
Manufacturer #: 5303281153
This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will not tumble, or if i...
$41.08
  In Stock
Order within the next 6 hrs and your part ships today!
Upper Drum Glide – Part Number: 5303937139
Upper Drum Glide
★★★★★
★★★★★
(28)
PartSelect #: PS470317
Manufacturer #: 5303937139
The upper drum glide is attached to the front panel of your dryer, you can locate it by removing the top portion of your dryer. The drum glide allows the drum to rotate with ease and little sound. The...
$51.79
  In Stock
Order within the next 6 hrs and your part ships today!
Drum Support Bearing – Part Number: 131825900
Drum Support Bearing
★★★★★
★★★★★
(19)
PartSelect #: PS418807
Manufacturer #: 131825900
If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which a...
$8.96
  In Stock
Order within the next 6 hrs and your part ships today!
Door Catch – Part Number: 131658800
Door Catch
★★★★★
★★★★★
(18)
PartSelect #: PS418433
Manufacturer #: 131658800
The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door...
$58.17
  In Stock
Order within the next 6 hrs and your part ships today!
M Series Ignition Coil Kit – Part Number: 5303931775
M Series Ignition Coil Kit
★★★★★
★★★★★
(24)
PartSelect #: PS470049
Manufacturer #: 5303931775
This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the ...
$35.04
  In Stock
Order within the next 6 hrs and your part ships today!
Lint Screen and Frame – Part Number: 131390300
Lint Screen and Frame
PartSelect #: PS417677
Manufacturer #: 131390300
This filter collects lint as it passes through the dryer vent.   No Longer Available
Dryer Drum Bearing Bracket – Part Number: 131724301
Dryer Drum Bearing Bracket
★★★★★
★★★★★
(2)
PartSelect #: PS12579101
Manufacturer #: 131724301
This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing
$10.50
  In Stock
Order within the next 6 hrs and your part ships today!
Flat Style Belt – Part Number: 5303281154
Flat Style Belt
★★★★★
★★★★★
(6)
PartSelect #: PS459830
Manufacturer #: 5303281154
This is a flat style ridgeless dryer belt.
$26.84
  In Stock
Order within the next 6 hrs and your part ships today!
Idler Pulley Assembly – Part Number: 5303212849
Idler Pulley Assembly
★★★★★
★★★★★
(3)
PartSelect #: PS457526
Manufacturer #: 5303212849
Use this idler pulley assembly with gas or electric clothes dryer that has a flat dryer belt. ***Please NOTE: This part has been redesigned by the manufacturer and may not fit your appliance.   No Longer Available
Door Strike – Part Number: 5303207102
Door Strike
★★★★★
★★★★★
(7)
PartSelect #: PS455020
Manufacturer #: 5303207102
The door strike is attached to the door of your dryer and holds the door closed. If your dryer door is not closing, this might be due to the door strike needing to be replaced. This is a simple repair...
$21.75
  In Stock
Order within the next 6 hrs and your part ships today!
Grounding Ball – Part Number: 5303281019
Grounding Ball
PartSelect #: PS459766
Manufacturer #: 5303281019
This grounding ball is used in dryers and works to prevent friction in the rear bearing when the drum rotates. If your dryer is making a squealing, loud, banging noise or will not operate, it is best ...
$16.24
  In Stock
Order within the next 6 hrs and your part ships today!
Flame Sensor – Part Number: 5303281135
Flame Sensor
★★★★★
★★★★★
(4)
PartSelect #: PS459818
Manufacturer #: 5303281135
This part senses the flame for heat allowing the gas valve to open. The most common issue that might arise that would indicate the flame sensor needs to be replaced is your dryer is not giving off eno...
$63.04
  In Stock
Order within the next 6 hrs and your part ships today!

Questions And Answers for 49-2828-00-01

Be the first to ask our experts a question about this model!

Common Symptoms of the 49-2828-00-01

[Viewing 7 of 7]
Noisy
Fixed by
these parts
Show All
No heat or not enough heat
Fixed by
these parts
Show All
Will not tumble
Fixed by
these parts
Show All
Marks left on clothes
Fixed by
these parts
Show All
Door won’t close
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Takes too long to dry
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loud Squeaking
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.
Parts Used:
Rear Drum Bearing Kit
  • Frank from Boyertown, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
319 of 328 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum glide wore down and caused close to get stuck between drum and front panel.
Unpluged dryer. Removed the top of dryer by pushing in a retaining clip on both sides of the front lip with a screw driver. Remove the two screws on both sides of front panel. These screws are square head or phillips #2. Unplugged the wiring harness to front panel (make sure power has been disconnected). Support drum and lean front panel away from dryer body. Front panel will pull off of tabs at bottom. The old drum glide is fiberous and hard to remove. I removed most of it with the pliers, but had to carefully scrape the balance of the glide off with the wood chisel. The adhesive that comes with the repair part has an acetone base, so I used acetone (or you could use nail polish remover) to remove the old adhesive. Once the acetone has dried, I applied an 1/8" snaking bead of adhesive to the front panel. There is more adhesive in the tube than you need so do not use too much. Make sure that you get adhesive as close to the base of the lower seal as you can. Follow directions on adhesive tube and then attach the glide. I let it set up for about 30 seconds. Place the front panel back on the tabs of the dryer. Carefully lift the drum an fit it on the front panel and insert the two screws holding the panel to the base. Reconnect the wiring harness and make sure it is not in contact with the drum. Check to make sure that all of the electrical connectors on the timer are still in place. Reassemble the dryer. Reconnect power.
Parts Used:
Upper Drum Glide
  • William from Boise, ID
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
181 of 248 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would heat initially then cool down
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.
Parts Used:
M Series Ignition Coil Kit
  • Brett from Monticello, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
90 of 102 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!