44-2407-23-03 Tappan Washer Parts & Repair Help | PartSelect
Models > 44-2407-23-03
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(10)
PartSelect #:PS815509
Manufacturer #:134190200
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the...
$31.47
In Stock
PartSelect #:PS417085
Manufacturer #:131168200
Sold individually.
$8.20
In Stock
PartSelect #:PS417463
Manufacturer #:131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, int...
$8.38
In Stock
PartSelect #:PS2331296
Manufacturer #:216858001
Sold Individually.
$6.41
In Stock
(1)
PartSelect #:PS473382
Manufacturer #:5308002401
The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for t...
$10.79
In Stock
PartSelect #:PS451084
Manufacturer #:5300633870
No Longer Available
PartSelect #:PS459613
Manufacturer #:5303280326
This v-style belt or drive belt is designed for use in your washing machine. This part connects the drive motor to the drive system in the washer, which spins the basket. If you no...
$20.39
On Order
PartSelect #:PS417749
Manufacturer #:131422100
Sold Individually.
No Longer Available
PartSelect #:PS3655064
Manufacturer #:137539500
Holds plated on Trunion .312-18 x 1.625.
$10.79
On Order
PartSelect #:PS474201
Manufacturer #:5308015493
This spacer is used in washers or a washer and dryer combo unit. Spacers are used to create space between cotter pins, lock nuts, hitch pins or to fill the space between machinery ...
$10.78
In Stock
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer Continued To Fill To Point Of Overflow

Water Inlet Valve – Part Number: 134190200
  • Customer: alvaro from east hampton, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 74 of 82 people found this instruction helpful
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connec... read more

Dryer wouldnt turn on

Terminal Block – Part Number: 134037400
  • Customer: Emily from Raleigh, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 26 of 40 people found this instruction helpful
I thought the problem was electrical so I inspected the power cord and noticed a burn on the ground connection. I disconnected the wires and inside the block was melted so I replaced it making sure the connection was tight between the power cord and block. It runs no problem. I think the dryer shorted because of a loose connection. read more

Leaking washing machine.

  • Customer: Ron from Williamsburg, MI
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 23 of 36 people found this instruction helpful
Removing the piece above the tub gasket was very difficult. A lot of hammer and chisel work.
15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove the old rubber stops.... read more