Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
422437-0750-01 Briggs and Stratton Engine - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air...
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "M...
This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in...
This Fuel Filter is a white plastic part attached within the fuel delivery system between the fuel tank and carburetor. Installation is rated as "Easy" and requires a set of pliers and a screwdriver. ...
This rewind starter spring or as it is also known, recoil spring, rewinds the pull robe back into the starter housing of your engine. The spring is made of metal, silver colored, and sold individually...
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
Ensure smooth and balanced operation of your Briggs and Stratton engine with this exceptional Gear Governor. It's intricately designed to maintain control over the speed of the engine, contributing to...
This is a manufacturer approved starter pinion gear designed for use with lawn and garden equipment engines. This Starter pinion gear is attach to the starter clutch drive and engages the flywheel to ...
This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to tra...
This is an authentic OEM sourced replacement part that is intended to be used with lawnmower engines and outboard motors from Briggs & Stratton and Toro. The metal screw is used to secure the rocker c...
This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The p...
$10.60
In Stock
Order now and your part arrives by Apr 6
Questions And Answers for 422437-0750-01
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Look on YouTube for video's on how to replace a Briggs governor. There are several there. My favorite, with best explanation, is, "Easily Replace Briggs Governor Gear (V-Twin Intek Engine) with Taryl". https://www.youtube.com/watch?v=wn3eanGxSEA&t=152s.
Taryl (probably not his real name) does a very good job of showing step-by-
... Read morestep the whole procedure, along with some additional hints/tricks/techniques of value.
Not including oil and filter, I spent less than $50 for a new governor, gasket, and drive shaft seal. That's all that is really necessary to replace is those three parts. That is, unless pieces of the old governor tore up a gear, valve, or something else. Inspect everything! {I was lucky and only the governor was destroyed}
One word of note. Be sure to clean out all of the debris from the blown governor. Be sure to remove the spark plugs and carefully rotate the drive shaft while looking for nooks-and-crannies where debris can hide. I tried to use a magnet to help, but it didn't help much, even though the block is aluminum.
