38HA-3TXW Magic Chef Range - Overview
Sections of the 38HA-3TXW
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Long Oven Sensor
PartSelect #: PS1570174
Manufacturer #: 12001656
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of...
$43.18
In Stock
Range Terminal Block
PartSelect #: PS11750972
Manufacturer #: WPW10245259
This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness...
$27.36
In Stock
Oven Door Spring
PartSelect #: PS11744749
Manufacturer #: WP7803P058-60
The oven door springs create tension which allows the door to open and close with ease. This spring can be used on either the left or right side of your oven, is made completely of metal, and is appro...
$15.00
In Stock
Bake Element (15 Inch long x 19 Inch wide)
PartSelect #: PS11757468
Manufacturer #: WPY04000041
This spade style bake element with push on wire terminals is 15 inches long and 19 inches wide. The depth of the terminals is three inches.
$79.80
In Stock
Hinge - Left Side
PartSelect #: PS1603106
Manufacturer #: 3418A029-34
The hinges allow the door to swing up and down. The hinges must be properly adjusted in order for the door to close properly.
No Longer Available
Hinge - Right Side
PartSelect #: PS1603107
Manufacturer #: 3418A030-34
The hinges allow the door to swing up and down. The hinges must be properly adjusted in order for the door to close properly.
No Longer Available
Electronic Relay Board
PartSelect #: PS11744534
Manufacturer #: WP7428P005-60
This board sends information (such as temperature of oven, bake, broil) to the main control board during specific functions.
No Longer Available
Broil Element Kit
PartSelect #: PS11757469
Manufacturer #: WPY04000042
This broil element is a little over seventeen inches long, and is not quite thirteen inches wide. It has screw on terminals and a terminal depth of just over three inches. The terminals are just two i...
No Longer Available
Questions And Answers for 38HA-3TXW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 38HA-3TXW
[Viewing 10 of 10]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Will not program
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening,
... Read more
reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Read less
Parts Used:
-
David from Westford, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
162 of 213 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F1-1 code
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Fa
... Read more
ilure to do so will cause the plastic plug connector to melt from oven heat.
Read less
Parts Used:
-
charles from marstons mills, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
79 of 110 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned terminal block and filter board
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Parts Used:
-
Joseph from Decatur, GA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
95 of 204 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!