Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This blade is sourced directly from the manufacturer for use in Craftsman and Husqvarna lawn mowers. The blade is the part of the mower that is responsible for cutting and mulching the grass. It is 22...
The Dust Shield is a 6-3/4 inch, black plastic part, used to prevent dust or debris fouling the wheel or axle. It attaches inside of the wheel around the axle. Installation is rated as "Easy" and will...
This Genuine OEM blade control cable assembly is designed for use with walk-behind and push lawn mowers. Sold individually, it includes a durable metal wire cable with Z-type bent ends, a rubberized p...
This genuine manufacturer sourced replacement part is designed for use with lawn mowers.It attached to the mower deck to protect your feet and legs from grass clippings and debris. It is made out of p...
It is a genuine OEM supplied item which is made for walk-behind lawn mowers. This is a high-quality replacement for a missing or a damaged pinion gear that helps to drive the mower's wheel. Unfortunat...
Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carr...
Introducing the Husqvarna Drive Control Cable! This high-quality ground drive cable is crucial for the efficiency of your lawn mower. With an impressive length of 65 1/2" and a conduit length of 55 1/...
The E-Ring 7/16 is a 7/16-inch silver, metal part which can be attached to various locations on a variety of equipment to snap into grooves and secure parts into place. This part will require pliers t...
This part has been sourced from the original manufacturer and is intended to be used with walk-behind lawnmowers from Husqvarna, Poulan, Weed Eater, and Jonsered. The metal pawl is used to secure the ...
This washer is not part of a kit or assembly. It is sold individually. With an O.D. of 1 inch, this OEM replacement part is made of dark grey metal and is used to provide a tight seal between the mowe...
This is a genuine manufacturer-sourced replacement screw which is specially designed for use with Craftsman lawn and garden equipment. It is a standard hardware which has multiple applications dependi...
A genuine item that is supplied by the original equipment manufacturer for use with lawn and garden equipment. It is a high-quality screw which has a few different applications depending on the model ...
$6.88
In Stock
Order now and your part arrives by Mar 19
Questions And Answers for 388182
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Pushed the cable through the engine mount.Connected the cable to the engine slider. Pulled cable through the previous tie down connected to the lower end of the bar. Attached the connector on the cable to the hole in the lawn mower bar near the top of the bar.. Attached the top end of the cable to the on/off bar where you push the mower.
Remove the front drive cover and disconnect the old from the drive, hook the new drive cable to the drive, and connect new cable back to the handle. Reinstalled the drive cover, started unit, and test that the drive was working correctly.
Removed wheel by pressing off the plastic hub cap exposing the nut holding the wheel. I removed the nut, then pulled the wheel straight off the axel shaft. This exposed the broken dust cover. I they wiggled the dust cover off, cleaned the dirt from inside the wheel, placed the new dust cover, replaced the wheel, nut and hub cap.
