Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This fuel tank assembly is supplied by the original manufacturer for use in trimmers. It is responsible for storing and transferring fuel to the engine for combustion. The assembly consists of a plast...
A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, ...
This genuine bump head knob assembly, sometimes known simply as the bump head, is black and approximately 2 inches long. Sold individually, this plastic part releases the cutting line. Over time, this...
This is a genuine OEM replacement part designed for use with some Handheld String Trimmers. This filter is made out of Foam and it is sold individually. The purpose of this filter is to keep dirt and ...
This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with trimmers and blowers. The gasket is used to seal the connection between the carbure...
This clutch assembly is a genuine OEM replacement kit for outdoor lawn equipment. The kit includes the clutch drum, clutch, clutch washer, and screw. The clutch assembly transfers power from the engin...
This is a manufacturer approved O-Ring designed for lawn and garden equipment. This is the O-Ring that provides an Air Tight seal between Carburetor and Cylinder Head. If doing maintenance on carburet...
This spool is for line trimmers.
Spool houses the cutting line and fits inside the cutting head to cut grass and weeds.
Wear work gloves to protect your hands when installing this part.
Genuine OEM replacement part, this item is sold individually. This spring is used on all of the trimmers listed below. It is installed between the inner reel and the outer spool assembly. Its purpose...
This is a genuine anti-rotation screw from the Ryobi manufacturer. The metal screw is compatible with many lawn and garden trimmers. This item works to help secure the clutch cover assembly. This part...
This authentic manufacturer-approved component which is specially designed for use with handheld lawn and garden equipment. The purpose of this o-ring is to provide an air-tight seal between connected...
Removed the two screws holding the fuel tank to the main unit. Removed the two fuel lines and any stuck on rubber. Installed and installed two screws to mount the new tank. Slid fuel lines on their respective connectors. Done.
emptied fuel from tank. pulled off the 2 fuel lines from the carburetor.opened the air cleaner door. removed the 2 torque screws that hold on the carburetor. removed the carburetor and air cleaner gasket. installed new carburetor and gasket and put back and tightened the 2 torque screws. closed air cleaner door and pushed the fuel lines o
... Read morento the new carburetor.put some fuel in the tank. started the trimmer. runs great.
The replacement of the carburetor, O-ring, and gasket was simple. I removed 2 screws that held the air cleaner and carburetor in place, swapped them out, and replaced the screws. What took longest was finding a piece of fuel line after breaking one of them. It was brittle after hanging in my garage for several years. I found some in my
... Read more garage and replaced it. It took a few pulls to get it started, but ran very smooth.
Additional information: rather than mixing my fuel, I purchased 40:1 pre-mix fuel to prevent gunking up the carburetor in the future. I use it in my other trimmer and have not had any issues.
