Models
>
21442
21442 Toro Lawn Mower - Overview
Models starting with 21442
Click on the best match to narrow your results.
Exact Part matches for your search term
[Viewing 2 of 2]
Axle Spacer
This part number matches the current model number 21442
PartSelect #: PS11947605
Manufacturer #: 21442
No Longer Available
SET SCREW
This part number matches the current model number 21442
PartSelect #: PS16563985
Manufacturer #: 21442
$3.99
Special Order
Keep searches simple, eg. "belt" or "pump".
Blade-22 Inch
PartSelect #: PS11804777
Manufacturer #: 131-4547-03
This is a genuine OEM replacement blade for use on Lawn Mowers. If the blade is too dull it will tear the grass instead of an even cut. A bent or damaged blade can cause serious damage or injuries. Yo...
$24.90
In Stock
V-Belt
PartSelect #: PS8849602
Manufacturer #: 117-1018
This is a genuine replacement v-belt sourced from original manufacturer and it is used on Toro lawn mowers. This part is made out of rubber and it is sold individually. This is the the belt that is at...
$21.54
In Stock
Nut-Lock, Ni
PartSelect #: PS9276436
Manufacturer #: 3296-29
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is use...
$3.99
In Stock
Ring-Retaining
PartSelect #: PS8950132
Manufacturer #: 32151-61
This metal retaining ring, otherwise known as a snap ring, holds parts in place in your lawn equipment, such as blades, shafts, pulleys, or other rotating components, to prevent them from sliding off ...
$3.99
In Stock
Support-Blade
PartSelect #: PS9257416
Manufacturer #: 108-3766-03
The Blade Support is a 6-x-3-inch Black, metal part used to support the blade. It's rated as "Easy" to install by customers. It must be torqued to manufacturer specifications which will require a sock...
$11.20
In Stock
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
trailing shield had broken off the mower, rendering bag useless.
-
Judy from PRINCETON, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench (Adjustable)
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Read less
Parts Used:
-
Ray from YARDLEY, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set, Wrench set
3 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!