2048778480 Kenmore Upright Vacuum - Instructions

I removed the two spring clips that hold the pump and two wire spring clips that hold the hoses. Then I had to pry the pump off the shaft (it was frozen with rust). Then I cleaned the shaft with sandpaper and installed the new pump (which, by the way, came the next day, thank you very much) which made my wife very happy, and I thank you for that , too.

We received the part we needed in a timely manner. First we took the back off the washer and found out later we didn't have to, because you can access the pump from the bottom of the Whirlpool washer and when we turned it on it's back a brass colored pin about 2" long fell out and we have no idea where it goes.Looking around the bottom frame we saw another pin in a plastic little cup mounted to the frame and another empty cup .So we changed the pump easy,put the pin in the empty cup and the washer runs great! That's our story.Still don't know what the pin is for,it's not on the parts schematic.

Frist I disconnected the water lines and power cord. Then I leaned the washer back against the wall. Removed the 2 pump retainers and then the pump. Next removed the 2 screws from the motor retainers and pulled off the retainers and motor. Then removed the 3 bolts from the Gear case. Then removed the cap from the top of the agitator with a flat screw driver. Then removed the bolt from the top of the gear shaft. and removed the auger and agitator assembly. Then removed the gear case from the washer. Next removed the slip ring and then the clutch from the top of the gear case. Next removed the 1/4" screws from cover of gear case and removed the cover. Found the top gear bad. Ordered the new gear and pinion kit. Couldn't find any part #'s to match what PartSelect had. Ordered the gear that they should that fit most washers. The pics they had up looked the same as the one that was bad. Had the new gear in 3 days put it back together and it still wouldn't work right. Took it apart again and looked at it and found a small clip on the bottom side of the gear was upside down. Fliped it over put the gear back in and ran the washer with the gear case out and it worked. Put it back together again. And learned a good lesson always watch how you take things apart for when it's time to put it back together!

1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamps.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]

I had to take the motor and transmission out. They are one piece. Removed the clutch, take off trans. cover, remove a snap ring, take the striped gear off, and put the new one on. Then put put everything back on the way it came off.

Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.

First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconnected hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!

Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
The corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.

flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer

Tilt machine on its side,snap off the two retaining straps and remove the pump and sanded the shaft on the electric drive motor to remove rust ,Install new pump and retaining straps and unit now running great.

I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.

On this model, no need to tip washer on back. Tilt console back and disconnect lid switch. Remove two clips holding back to top of washer (under console). Then remove top and front as directed in the video. The pump is accessible from the front of the unit, just below the tub. Hose clamps are easy to remove/replace. Took more time to wipe inside of washer clean than to remove/replace the water pump. Total time was just over 30 minutes.

The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.

Put new one on work good, but now can't pump no more .the problem now is the spin cycal broke and I not going to fix it. Thank for the part work good.

We unscrewed the two screws at the back of the control panel. Holding the control panel on both ends
we pulled it toward the front of the machine, slightly and gently lifting it at the same time, removing it from the metal surround. Holding the control panel up off of the surround we rocked the surround forward and lifted it off the washing machine frame.
We could see where the leak was coming from. We took the hose clamps from the two ports, then
using a pair of pliers pulled the two clips that are holding the pump onto the shaft protruding from the
electric motor. We matched up the part on the web sight. Ordered the part then when it came in we just reversed the order putting the machine back together. The hardest and most time consuming
thing about this repair was the clean up of the washing machine. (Dirt and soap residue does
build up on the inside of the wash tubs.)