Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a replacement carburetor overhaul kit for your small engine. The carburetor is essential to the overall performance of your engine, and the carb can get clogged up over time for a variety of r...
The Air Cleaner Gasket is used to provide a seal between the air cleaner base, and carburetor. It's a gray, composite material part, which is rated as "Easy" to install and will require a screw driver...
This is an original Craftsman part for use with Lawn Mowers. The carburetor primer bulb circulates fuel to the carburetor to provide quicker starting. The most common reasons for replacing the primer ...
This needle and seat kit, also known as a float valve, is found in many types of liquid-fueled lawn equipment, such as carburetors. The valve regulates the flow of fuel into the float bowl. The needle...
This genuine OEM engine gasket set is sourced directly from the manufacturer and includes the gaskets needed to seal the components in a gas-powered engine. This set ensures proper fit and performance...
The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. I...
Upgrade your equipment with this reliable Pulley/Spring Assembly from Briggs and Stratton. Known for their superior quality, Briggs and Stratton parts are designed to help prolong the life of your mac...
This part is the replacement gasket for the crankcase on your engine. The gasket helps to create a seal on the crankcase and prevent leaks. If you notice that your engine is not running at peak perfor...
This is a Genuine OEM Authorized Gasket used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recom...
This authentic OEM starter assembly is designed for use with lawn and garden engines and is sourced directly from the original manufacturer to ensure quality and compatibility. The assembly includes a...
This item is an authentic replacement part that has been sourced from the original manufacturer to be used with lawnmower engines from Briggs & Stratton and Toro. The metal float bowl fits onto the bo...
This is a genuine OEM sourced replacement part. It is designed for use with lawn and garden engines. It is an important part of the starter assembly that is used to crank start the unit. Please note s...
I found the model number of the Briggs & Stratton engine on the inside of the engine housing. Ordered a new starter-rewind unit, as the old cord broke and the thing was well worn. The instructions were clear enough, but to get the old starter off I had to drill out four rivets, which just spin around when you try. I used a hacksaw, chisel
... Read more, pliers, whatever worked on each rivet; this took a while. When they were finally removed, the new starter pull unit was relatively easy to install with the small nuts and bolts provided. On the Yard Machines log splitter, putting back the engine housing is quite tricky; you have to jostle the thing into place, get the pull handle above the cover and line up the bolt holes.
All the gaskets needed to be replaced on the Briggs 6.75 flathead I was rebuilding. I ported and polished the ports and shaved the eyebrow between the valves and the piston. The gasket set was a perfect fit. It is a monster now. It doesn't sound like a lawnmower engine anymore
