Models
>
20016
20016 (250000001-250999999 - 2005) Toro Lawn Mower - Overview
Sections of the 20016
[Viewing 12 of 12]Exact Part matches for your search term
[Viewing 1 of 1]
PLUG
Special Order
This part number matches the current model number 20016
PartSelect #: PS16563517
Manufacturer #: 20016
$3.48

Keep searches simple, eg. "belt" or "pump".

Washer-Stepped
In Stock
Order within the next 8 hrs and your part ships today!
PartSelect #: PS9048394
Manufacturer #: 614426
The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. I...
$2.99



Screw
In Stock
Order within the next 8 hrs and your part ships today!
PartSelect #: PS9053486
Manufacturer #: 650898A
This screw, also known as a shoulder bolt, is a genuine OEM replacement part for your lawn mower. This metal screw holds the starter grille in place against the rewing starter on your lawn mower. It r...
$2.99



Ring-Clip, Locking
In Stock
Order within the next 8 hrs and your part ships today!
PartSelect #: PS9052921
Manufacturer #: 65-2720
This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secure...
$2.99



Screw-Taptite
In Stock
Order within the next 8 hrs and your part ships today!
PartSelect #: PS9180925
Manufacturer #: 95-1726
$2.99



Spring-Compression
In Stock
Order within the next 8 hrs and your part ships today!
PartSelect #: PS8961286
Manufacturer #: 39-9650
$2.99



Blade-22 Inch
In Stock
Order within the next 8 hrs and your part ships today!
PartSelect #: PS11804777
Manufacturer #: 131-4547-03
This is a genuine OEM replacement blade for use on Lawn Mowers. If the blade is too dull it will tear the grass instead of an even cut. A bent or damaged blade can cause serious damage or injuries. Yo...
$27.91



Bowl Gasket Tecumseh
In Stock
Order within the next 8 hrs and your part ships today!
PartSelect #: PS9958948
Manufacturer #: 49-841
This OEM Carburetor Bowl Gasket attaches between the carburetor bowl and carburetor in order to seal the parts together. This model is rubber, black, and comes individually sold. Installation is rated...
$2.99



Bearing-Ball
In Stock
Order within the next 8 hrs and your part ships today!
PartSelect #: PS8824569
Manufacturer #: 104-8699
$3.79


Questions And Answers for 20016
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lost PartSelect Number PS9053486; Tecumseh 650898A screw
I lost two of the screws that hold the plastic Lawn Boy cowling to the Tecumseh lv195ea engine. I just replaced the lost screws with the newly ordered screws.
Parts Used:
-
Steven from FAIRVIEW, TN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The hub that the mower blade mounts to was broken
The hub that the mower blade mounts to was brokenPut the new Harbonne played and played securing flange bolted it up
Parts Used:
-
randy from HIGHLAND, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Parts Used:
-
Ray from YARDLEY, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set, Wrench set
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!