Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty...
This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and ...
This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part ...
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need...
This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant t...
The flange sleeve bearing, also known just as the bearing, is sold individually, and assists the tine shaft rotation on your tiller by reducing friction between the moving parts and securing their pos...
Designed for use in various models of lawn and garden equipment, this part is not sold as part of a kit or assembly. It is made of metal, is gold in color, and is sold individually. This part may also...
Ensure smooth and balanced operation of your Briggs and Stratton engine with this exceptional Gear Governor. It's intricately designed to maintain control over the speed of the engine, contributing to...
This is a manufacturer approved starter pinion gear designed for use with lawn and garden equipment engines. This Starter pinion gear is attach to the starter clutch drive and engages the flywheel to ...
It is an authentic part that is supplied by the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this gasket is ...
Also referred to as a Lock Nut or Flange Lock, this nut is designed for use with various lawn and garden equipment. The purpose of this part is to hold parts in place while resisting loosening when pr...
This is a genuine manufacturer sourced replacement part designed for lawn and garden equipment engines. This gasket provides an air-tight seal for the float bowl. Over time this gasket will shrink, be...
$12.92
In Stock
Order now and your part arrives by Apr 23
Questions And Answers for 17BA5A7P709
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set
... Read more valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t
... Read moreo remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Look on YouTube for video's on how to replace a Briggs governor. There are several there. My favorite, with best explanation, is, "Easily Replace Briggs Governor Gear (V-Twin Intek Engine) with Taryl". https://www.youtube.com/watch?v=wn3eanGxSEA&t=152s.
Taryl (probably not his real name) does a very good job of showing step-by-
... Read morestep the whole procedure, along with some additional hints/tricks/techniques of value.
Not including oil and filter, I spent less than $50 for a new governor, gasket, and drive shaft seal. That's all that is really necessary to replace is those three parts. That is, unless pieces of the old governor tore up a gear, valve, or something else. Inspect everything! {I was lucky and only the governor was destroyed}
One word of note. Be sure to clean out all of the debris from the blown governor. Be sure to remove the spark plugs and carefully rotate the drive shaft while looking for nooks-and-crannies where debris can hide. I tried to use a magnet to help, but it didn't help much, even though the block is aluminum.
