Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The Dust Shield is a 6-3/4 inch, black plastic part, used to prevent dust or debris fouling the wheel or axle. It attaches inside of the wheel around the axle. Installation is rated as "Easy" and will...
The is a genuine OEM part. The rear wheel & tire assembly is compatible with many Husqvarna lawn mowers. This component is fitted on the shaft assembly, between the washer and the flangelock hex nut. ...
Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carr...
The E-Ring 7/16 is a 7/16-inch silver, metal part which can be attached to various locations on a variety of equipment to snap into grooves and secure parts into place. This part will require pliers t...
This part has been sourced from the original manufacturer and is intended to be used with walk-behind lawnmowers from Husqvarna, Poulan, Weed Eater, and Jonsered. The metal pawl is used to secure the ...
This is a genuine Craftsman part for use with Lawn Mowers. The drive gear attaches on the inner side of the drive wheel. The drive gear meshes with the pinion in the drive wheel to propel the mower. T...
It is a genuine OEM sourced replacement drive belt that is used on Husqvarna walk-behind lawn mowers. This is the main belt that drives the unit. Over time belts tend to wear out or stretch eventually...
This washer is not part of a kit or assembly. It is sold individually. With an O.D. of 1 inch, this OEM replacement part is made of dark grey metal and is used to provide a tight seal between the mowe...
This is a genuine manufacturer-sourced replacement screw which is specially designed for use with Craftsman lawn and garden equipment. It is a standard hardware which has multiple applications dependi...
A genuine item that is supplied by the original equipment manufacturer for use with lawn and garden equipment. It is a high-quality screw which has a few different applications depending on the model ...
This is a genuine Husqvarna replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor....
$13.15
In Stock
Order now and your part arrives by Jul 17
Questions And Answers for 143RII
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
9/16s inch socket, something to prop up one side of the mower (I used a plastic plant pot), and about 5 minutes was all that was needed. Undo the nut on the wheel, remove, replace it with the new one (can't mess it up - just goes on one way which is extremely obvious), replace and tighten the nut -- done. Just that simple. With the new
... Read morekicks it goes up hill like a champ now (instead of spinning, especially with the grass catcher attached).
Can't believe you all had replacement wheels for this dinosaur. They have drive gears attached to wheel. Very simple to fix but broke old exhaust chute on mower when I leaned it on its side. Now I have to find a replacement for it! Geeesh!!!
Removed wheel by pressing off the plastic hub cap exposing the nut holding the wheel. I removed the nut, then pulled the wheel straight off the axel shaft. This exposed the broken dust cover. I they wiggled the dust cover off, cleaned the dirt from inside the wheel, placed the new dust cover, replaced the wheel, nut and hub cap.
