13AJ689G766 (2004) Troy-Bilt Lawn Tractor - Overview
Sections of the 13AJ689G766
[Viewing 8 of 8]
Keep searches simple, eg. "belt" or "pump".
Joint
PartSelect #: PS9171232
Manufacturer #: 923-0448A
The Lock Ball Joint Assembly is part of the steering mechanism, and the machine will not be able to steer without it. This part attaches to the steering block and drag link. Installation is rated as "...
$29.47
In Stock
Lawn Mower Solenoid
PartSelect #: PS9310446
Manufacturer #: 925-1426A
This starter solenoid is designed to reliably engage the starter motor by allowing a low-power ignition signal to trigger the high-current starting circuit. Built for dependable performance, it helps ...
$31.58
In Stock
Washer-lock 5/16
PartSelect #: PS9311087
Manufacturer #: 936-0119
This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent ...
$6.57
In Stock
Nut-lock 1/4
PartSelect #: PS9155135
Manufacturer #: 912-3027
This genuine OEM supplied part is specially designed for use with a variety of lawn and garden equipment. It is a standard hardware which may have multiple applications. Make sure to refer to the appr...
$6.40
In Stock
Battery 245 CCA Dry
PartSelect #: PS9310460
Manufacturer #: 925-1707D
NOTE: Battery is not charged and does not include electrolyte or acid.
No Longer Available
Lawn Mower Keys (Pair)
PartSelect #: PS9171554
Manufacturer #: 925-0201
This pair of keys is supplied by the equipment manufacturer for use in lawn and outdoor power equipment. The key is made of metal and designed to prevent unauthorized use or accidental starting of the...
$13.37
In Stock
Ball Bearing
PartSelect #: PS9167899
Manufacturer #: 941-0600
This is a genuine OEM sourced replacement part that is intended to be used with lawnmowers, snowthrowers, and tillers from Bolens, Ryobi, Yard Machines, MTD, Troy-Bilt, and Yard-Man. The sealed bearin...
$32.57
In Stock
Lock Nut
PartSelect #: PS16410294
Manufacturer #: 712-3004A
This OEM Top Locknut measures 5/16x18, is made of metal, and it isused to secure parts in place and prevent backing out from vibration. Replacing this part varies in difficulty depending on the part...
$6.40
On Order
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Yardman / MTD wouldn't steer left, makes a popping and grinding noise when turning.
To disconnect the steering shaft to replace the bearing, there is a #3 Philips head screw on the underside of the deck which needs to be taken out. Chances are it hasn't been replaced before, so it is likely very tight. I ended up dropping the deck to allow for more room but it could probably be done with the deck in place the way I had t
... Read more
o do it. I had someone hold the steering wheel up top (not undoing the 13mm bolt holding the steering wheel in) and tried to unscrew the Philips, even after heating it with a torch still stripped out. The only way I could get the screw out was to take a pair of Vice Grips adjusted extremely tight to the outside of the screw and put the torch on it to heat it again. Then, turn the steering wheel to the left and when the Vice Grips get caught on the bottom of the mower, it will unthread the steering wheel from the screw. After the screw and washer are out *TAKE NOTE OF THE ORIENTATION OF THE WASHER*, I went to the hardware store and replaced the screw with a bolt that was 5/16 - 18 x .750 which was the closest length they had, took out the worn out bearing, popped in the new one, reinstalled the washer and bolt, then the deck. Even if you get the philips screw out without using Vice Grips, I would still recommend replacing it with a bolt.
Read less
Parts Used:
-
Patrick from Northville, NY
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
7 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!