13AG619H022 MTD Lawn Mower - Overview
Models starting with 13AG619H022
Click on the best match to narrow your results.
- 13AG619H022 (2002) MTD Lawn Mower (MTD Lawn Mower Model 13AG619H022/2002 Parts)
- 13AG619H022 (2003) MTD Lawn Mower (MTD Lawn Mower Model 13AG619H022/2003 Parts)
- 13AG619H022 (2000) MTD Lawn Mower (MTD Lawn Mower Model 13AG619H022/2000 Parts)
- 13AG619H022 (2001) MTD Lawn Mower (MTD Lawn Mower Model 13AG619H022/2001 Parts)
Keep searches simple, eg. "belt" or "pump".
Lawn Mower Hex Washer Head Screw
PartSelect #: PS9298768
Manufacturer #: 710-0599
This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part ...
$6.40
In Stock
Lawn Mower Flange Bearing
PartSelect #: PS9122043
Manufacturer #: 741-0660A
This OEM-manufactured flange bearing supports and enables the smooth rotation of parts in your lawn equipment, such as the blade assembly, axle assembly, or steering components. This bearing has an in...
$6.40
In Stock
Lawn Mower Key
PartSelect #: PS9310468
Manufacturer #: 925-1745A
This manufacturer-certified Ignition Key comes in black/silver and is used in the ignition slot to turn on the engine. If your key becomes damaged or lost (which these small keys easily are), this pa...
$24.45
In Stock
Lawn Mower Steering Pinion Gear
PartSelect #: PS9108026
Manufacturer #: 717-1554
This steering gear is an original part from Craftsman for lawn tractors. This piece is part of the tractors steering mechanism. This steering gear maneuvers the steering sector gear to move the lawn t...
$16.91
In Stock
Bushing-.380 Id
PartSelect #: PS9167515
Manufacturer #: 941-0475
This is an authentic OEM part for Craftsman lawn and garden equipment. This bushing has an internal diameter of 0.380", is made of durable black plastic, is not part of an assembly or kit, and is sold...
$6.40
In Stock
Joint
PartSelect #: PS9171232
Manufacturer #: 923-0448A
The Lock Ball Joint Assembly is part of the steering mechanism, and the machine will not be able to steer without it. This part attaches to the steering block and drag link. Installation is rated as "...
$29.47
In Stock
Mulching Blade
PartSelect #: PS9167946
Manufacturer #: 942-0616A
Dimension: 21.23-Inch
This is a Genuine Manufacturer Approved Blade used on Riding Mower/Lawn Tractor. This Blade is sold Individually. It is a 3-in-1 blade for mulch, bag and side discharge purpos...
$36.85
In Stock
Lawn Mower Plastic Flange Bearing
PartSelect #: PS9302372
Manufacturer #: 741-0487C
Made of durable silver plastic, this Flange Bearing is an authentic manufacturer-source replacement part for hundreds of models of lawn and garden equipment. It is used to allow a shaft to connect whi...
$10.54
In Stock
Belt
PartSelect #: PS9171696
Manufacturer #: 954-0349
This replacement belt is sourced directly from original equipment manufacturer. It is a genuine OEM sourced item commonly used on lawn mowers and tractors. This is the the belt that drives the mower b...
$47.40
In Stock
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Yardman / MTD wouldn't steer left, makes a popping and grinding noise when turning.
To disconnect the steering shaft to replace the bearing, there is a #3 Philips head screw on the underside of the deck which needs to be taken out. Chances are it hasn't been replaced before, so it is likely very tight. I ended up dropping the deck to allow for more room but it could probably be done with the deck in place the way I had t
... Read more
o do it. I had someone hold the steering wheel up top (not undoing the 13mm bolt holding the steering wheel in) and tried to unscrew the Philips, even after heating it with a torch still stripped out. The only way I could get the screw out was to take a pair of Vice Grips adjusted extremely tight to the outside of the screw and put the torch on it to heat it again. Then, turn the steering wheel to the left and when the Vice Grips get caught on the bottom of the mower, it will unthread the steering wheel from the screw. After the screw and washer are out *TAKE NOTE OF THE ORIENTATION OF THE WASHER*, I went to the hardware store and replaced the screw with a bolt that was 5/16 - 18 x .750 which was the closest length they had, took out the worn out bearing, popped in the new one, reinstalled the washer and bolt, then the deck. Even if you get the philips screw out without using Vice Grips, I would still recommend replacing it with a bolt.
Read less
Parts Used:
-
Patrick from Northville, NY
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
7 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!