13AD608G101 (1H019H - 1H310H) Cub Cadet Lawn Mower - Overview
Sections of the 13AD608G101
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Engine Oil Seal
PartSelect #: PS9151828
Manufacturer #: 795387
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty...
$9.69
In Stock
Connector-hose
PartSelect #: PS9074730
Manufacturer #: 692317
This is a Genuine Manufacturer Sourced replacement part used on a a variety of Engines. This is a Fuel Line Connector connects the fuel line to the carburetor. This part is made out of Plastic and Met...
$9.08
In Stock
Engine Cylinder Head Gasket
PartSelect #: PS9067184
Manufacturer #: 693997
This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and ...
$30.09
In Stock
Gasket Set-valve
PartSelect #: PS9141388
Manufacturer #: 794152
When it's time for your beloved 2 dishwasher to look and perform its best again, our 2 Outer Door Panel Assembly is your reliable friend. Crafted with precision in a smart stainless steel finish, this...
$44.73
In Stock
Lawn Mower Hex Washer Head Screw
PartSelect #: PS9298768
Manufacturer #: 710-0599
This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part ...
$6.40
In Stock
Gasket-exhaust
PartSelect #: PS9294808
Manufacturer #: 692236
This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in...
$6.47
In Stock
Crankcase Gasket With Bolts
PartSelect #: PS11829358
Manufacturer #: 594195
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need...
$53.18
In Stock
Seal-o Ring
PartSelect #: PS9294749
Manufacturer #: 691917
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and ma...
$6.40
In Stock
Gasket-exhaust
PartSelect #: PS9063564
Manufacturer #: 690970
This is a genuine OEM sourced replacement exhaust gasket. It is specially made for use with Briggs and Stratton engines commonly used on Toro lawn and garden equipment. Its purpose is to provide an ai...
$6.40
In Stock
Lawn Mower Steering Pinion Gear
PartSelect #: PS9108026
Manufacturer #: 717-1554
This steering gear is an original part from Craftsman for lawn tractors. This piece is part of the tractors steering mechanism. This steering gear maneuvers the steering sector gear to move the lawn t...
$16.91
In Stock
Armature-magneto
PartSelect #: PS9045176
Manufacturer #: 591459
Discover the Briggs and Stratton Armature-Magneto, a vital component for optimal operation of your lawn and garden equipment engines. This premium-quality ignition coil significantly contributes to sp...
$56.10
In Stock
Gear-governor
PartSelect #: PS9151758
Manufacturer #: 793338
Ensure smooth and balanced operation of your Briggs and Stratton engine with this exceptional Gear Governor. It's intricately designed to maintain control over the speed of the engine, contributing to...
$40.69
Special Order
Common Symptoms of the 13AD608G101
[Viewing 3 of 3]Engine misfires
Fixed by
these parts
these parts
Show All
Excess blue smoke from engine
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Engine quit due to valve guide sliding out causing rocker arm to be immovable resulting in bent push rods.
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set
... Read more
valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
Read less
Parts Used:
-
D from HUNTSVILLE, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
19 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
i NEEDED A DRIVE BELT FOR MY RIDING MOWER
1) DON'T ORDER FROM THESE IDIOTS.
2) THEY SENT THE WRONG BELT
3) THEY HAVE A CUSTOMER -NO- SERVICE NUMBER.
4) CAN'T GET A GOODS RETURN ONLINE
2) THEY SENT THE WRONG BELT
3) THEY HAVE A CUSTOMER -NO- SERVICE NUMBER.
4) CAN'T GET A GOODS RETURN ONLINE
Parts Used:
-
TERRY from OAK CREEK, WI
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
14 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t
... Read more
o remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Read less
Parts Used:
-
rodney from MUSCATINE, IA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Socket set
17 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!