Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
13AA604F401 (2002) Yard Man Lawn Tractor - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part ...
This manufacturer-certified Ignition Key comes in black/silver and is used in the ignition slot to turn on the engine. If your key becomes damaged or lost (which these small keys easily are), this pa...
This steering gear is an original part from Craftsman for lawn tractors. This piece is part of the tractors steering mechanism. This steering gear maneuvers the steering sector gear to move the lawn t...
This is an authentic OEM part for Craftsman lawn and garden equipment. This bushing has an internal diameter of 0.380", is made of durable black plastic, is not part of an assembly or kit, and is sold...
This is a Genuine replacement Belt designed for use with Riding Lawn Tractors/Mowers. This part is made out of Rubber and it is Sold Individually. This is the the Belt that drives your unit.
Make s...
The Lock Ball Joint Assembly is part of the steering mechanism, and the machine will not be able to steer without it. This part attaches to the steering block and drag link. Installation is rated as "...
This replacement upper drive belt is a genuine part. It is supplied from original equipment manufacturer for use with riding lawn mowers/tractors. This is one of the belts that drives the mower. When ...
Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between variou...
When the brakes are applied, this brake puck presses against the brake disc in your lawn equipment to help slow down or stop it. The brake puck is in the brake assembly, which might be located near th...
To disconnect the steering shaft to replace the bearing, there is a #3 Philips head screw on the underside of the deck which needs to be taken out. Chances are it hasn't been replaced before, so it is likely very tight. I ended up dropping the deck to allow for more room but it could probably be done with the deck in place the way I had t
... Read moreo do it. I had someone hold the steering wheel up top (not undoing the 13mm bolt holding the steering wheel in) and tried to unscrew the Philips, even after heating it with a torch still stripped out. The only way I could get the screw out was to take a pair of Vice Grips adjusted extremely tight to the outside of the screw and put the torch on it to heat it again. Then, turn the steering wheel to the left and when the Vice Grips get caught on the bottom of the mower, it will unthread the steering wheel from the screw. After the screw and washer are out *TAKE NOTE OF THE ORIENTATION OF THE WASHER*, I went to the hardware store and replaced the screw with a bolt that was 5/16 - 18 x .750 which was the closest length they had, took out the worn out bearing, popped in the new one, reinstalled the washer and bolt, then the deck. Even if you get the philips screw out without using Vice Grips, I would still recommend replacing it with a bolt.
_WW_1.gif "Page A Diagram and Parts List for 2002 Yard Man Lawn Tractor")
_WW_2.gif "Page B Diagram and Parts List for 2002 Yard Man Lawn Tractor")
_WW_3.gif "Page C Diagram and Parts List for 2002 Yard Man Lawn Tractor")
_WW_4.gif "Page D Diagram and Parts List for 2002 Yard Man Lawn Tractor")
_WW_5.gif "Page E Diagram and Parts List for 2002 Yard Man Lawn Tractor")
_WW_6.gif "Page F Diagram and Parts List for 2002 Yard Man Lawn Tractor")
_WW_7.gif "Page G Diagram and Parts List for 2002 Yard Man Lawn Tractor")
_WW_8.gif "Page H Diagram and Parts List for 2002 Yard Man Lawn Tractor")
