Models
>
13A0663F352
13A0663F352 Yard Machines Lawn Mower - Overview
Sections of the 13A0663F352
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Lock Ball Joint Assembly
PartSelect #: PS9171232
Manufacturer #: 923-0448A
The Lock Ball Joint Assembly is part of the steering mechanism, and the machine will not be able to steer without it. This part attaches to the steering block and drag link. Installation is rated as "...
$24.65
In Stock
Fl. Bearing
PartSelect #: PS9302372
Manufacturer #: 741-0487C
Made of durable silver plastic, this Flange Bearing is an authentic manufacturer-source replacement part for hundreds of models of lawn and garden equipment. It is used to allow a shaft to connect whi...
$7.51
In Stock
Washer-Lock 5/16
PartSelect #: PS9311087
Manufacturer #: 936-0119
This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent ...
$4.99
In Stock
Blade, 3-In-1
PartSelect #: PS9167944
Manufacturer #: 942-0610A
(Sold Individually)
This 3-in-1 blade is for lawn tractors.
The 3-in-1 blade combines the features of a high-lift blade and a mulching blade, and is used for discharging, bagging or mulching g...
$29.27
In Stock
Push Cap
PartSelect #: PS9300605
Manufacturer #: 726-0214
The Push Cap is a black plastic cap which secures to the end of a shaft to prevent injury. It can be installed with a hammer and is rated as "Easy" to install. If the part appears damaged or worn down...
$9.96
In Stock
Questions And Answers for 13A0663F352
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Mixer began to make a noise on speed two and higher
We took our 30 plus year mixer apart. I removed the old grease. There was some crumbly looking grease in the main housing gear section where the nylon gear is located. It looked like it had flour mixed in it. Not certain. Removed as best possible all old grease and applied 6 oz. of new Benalene grease to all of the gears. Now it do
... Read more
es not make the slight howl sound.
Read less
Parts Used:
-
LISA M from BATESVILLE, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Battery tray rusted out
Removed battery then replaced tray it sets in then, then reinstalled the battery
Parts Used:
-
Brian from LAGRANGE, KY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Yardman / MTD wouldn't steer left, makes a popping and grinding noise when turning.
To disconnect the steering shaft to replace the bearing, there is a #3 Philips head screw on the underside of the deck which needs to be taken out. Chances are it hasn't been replaced before, so it is likely very tight. I ended up dropping the deck to allow for more room but it could probably be done with the deck in place the way I had t
... Read more
o do it. I had someone hold the steering wheel up top (not undoing the 13mm bolt holding the steering wheel in) and tried to unscrew the Philips, even after heating it with a torch still stripped out. The only way I could get the screw out was to take a pair of Vice Grips adjusted extremely tight to the outside of the screw and put the torch on it to heat it again. Then, turn the steering wheel to the left and when the Vice Grips get caught on the bottom of the mower, it will unthread the steering wheel from the screw. After the screw and washer are out *TAKE NOTE OF THE ORIENTATION OF THE WASHER*, I went to the hardware store and replaced the screw with a bolt that was 5/16 - 18 x .750 which was the closest length they had, took out the worn out bearing, popped in the new one, reinstalled the washer and bolt, then the deck. Even if you get the philips screw out without using Vice Grips, I would still recommend replacing it with a bolt.
Read less
Parts Used:
-
Patrick from Northville, NY
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!